Eaton DRQ125-R47-R 1:1 Coupled Drum Core, 0.47 uH
Eaton DRQ125-R47-R 1:1 Coupled Drum Core, 0.47 uH

Eaton DRQ125-R47-R 1:1 Coupled Drum Core, 0.47 uH

Share
Eaton DRQ125-R47-R: Dual Winding Shielded Drum Core Inductor, 0.47 uH, 17.6 A, DCR 1.8 mOhm.
    • Product Details
    • Download

    Eaton DRQ125-R47-R 1:1 Coupled Drum Core, 0.47 uH

    DRQ125-R47-R at a glance: dual-winding shielded drum core, 0.47 uH per winding, 17.6 A, DCR 1.8 mOhm.

    Key Specifications

    ParameterValue
    Orderable part numberDRQ125-R47-R
    Rated inductance0.47 uH ±20%
    Open circuit inductance (OCL)0.46 uH
    Irms (40 °C rise)17.6 A
    Isat33 A
    DCR typical @ 20 °C1.8 mOhm
    Volt-microsecond rating3.17 V-us
    Series connection1.82 uH, 8.8 A
    Parallel connection0.47 uH, 17.6 A
    Turns ratio1:1, coupled
    Package12.5 x 12.5 mm footprint, 6.0 mm max height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    Two windings on one core, and that is the whole idea: wire them in parallel and you get a high-current choke with a quarter of the inductance; wire them in series and you get four times the inductance at half the current. Same part, two very different components.

    The arithmetic is the usual one for coupled windings: parallel gives L/4 with 2x the current capability, series gives 4L with half. DCR follows the same rule - parallel halves the resistance, series doubles it.

    Isat is the peak current for approximately 30% rolloff at +20 °C. In a buck converter the inductor current peaks at the top of the ripple, so the peak - not the average - is the number that has to stay below Isat with margin for the transient.

    Series Positioning

    DRQ125 is the 12.5 mm dual-winding part at 6.0 mm height. Wire the windings in parallel for a high-current single inductor, in series for a high-inductance choke, or leave them coupled as a 1:1 transformer for a SEPIC or flyback.

    • Typical applications: Desktop and server power, DC-DC converters, SEPIC/flyback transformer use, LCD panels, filter chokes.
    • Coupling changes the ripple: a coupled inductor in a multi-phase converter can cancel ripple, but only if the phases are driven with the right duty cycle.
    • Data sheet DS4311.

    Sizing and Layout Notes

    Choose 0.47 uH when the ripple target is at the low end of the design window: the DCR stays at 1.8 mOhm and the saturation limit at 33 A leaves the transient room it needs.

    Thermal design is not optional here. The rated current assumes a 40 °C rise with the part in free air on a stated pad; inside a closed box, on a thin board, next to a hot IC, that assumption is gone.

    Frequently Asked Questions

    Which connection do I use?
    Parallel for a high-current single inductor, series for high inductance at lower current, and coupled when you are building a SEPIC, flyback or a ripple-cancelling multiphase stage.

    Can I use it as a flyback transformer?
    Yes, within the isolation and the 1:1 ratio. Check the reflected voltage and the leakage inductance, because leakage is what creates the spike on the switch node.

    What is the OCL in parallel mode?
    With the windings paralleled the effective inductance is a quarter of the single-winding OCL; the datasheet lists the parallel rating explicitly.

    Design note: decide the connection before you lay out the board. Parallel, series and coupled all use the same part, and the inductance moves by 4x between them.

    Mechanical Dimensions

    eaton-drq-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products