Eaton DRQ127-150-R - Dual Winding 15 uH Power Inductor
Eaton DRQ127-150-R - Dual Winding 15 uH Power Inductor

Eaton DRQ127-150-R - Dual Winding 15 uH Power Inductor

Share
Eaton DRQ127-150-R: Dual Winding Shielded Drum Core Inductor, 15 uH, 5.03 A, DCR 24.7 mOhm.
    • Product Details
    • Download

    Eaton DRQ127-150-R - Dual Winding 15 uH Power Inductor

    DRQ127-150-R at a glance: dual-winding shielded drum core, 15 uH per winding, 5.03 A, DCR 24.7 mOhm.

    Electrical Specifications

    ParameterValue
    Orderable part numberDRQ127-150-R
    Rated inductance15 uH ±20%
    Open circuit inductance (OCL)14.1 uH
    Irms (40 °C rise)5.03 A
    Isat9.66 A
    DCR typical @ 20 °C24.7 mOhm
    Volt-microsecond rating20.3 V-us
    Series connection56.4 uH, 2.51 A
    Parallel connection15 uH, 5.03 A
    Turns ratio1:1, coupled
    Package12.5 x 12.5 mm footprint, 8.0 mm max height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    How to Read These Ratings

    Two windings on one core, and that is the whole idea: wire them in parallel and you get a high-current choke with a quarter of the inductance; wire them in series and you get four times the inductance at half the current. Same part, two very different components.

    The arithmetic is the usual one for coupled windings: parallel gives L/4 with 2x the current capability, series gives 4L with half. DCR follows the same rule - parallel halves the resistance, series doubles it.

    Saturation degrades with temperature on ferrite. Isat is the peak current for approximately 30% rolloff at +20 °C, and the hot value is the one that matters under a hood or inside a sealed enclosure.

    What This Family Is For

    DRQ127 is the tallest dual-winding DRQ at 8.0 mm and the highest-current part in the family, up to 56 A peak in parallel mode. Two windings, one core, and the option to use it as a transformer.

    • Typical applications: High current DC-DC, server power, SEPIC and flyback, battery systems, filter chokes.
    • The parallel rating is not double the single-winding rating of the same size - check both windings' DCR and the thermal path before assuming it.
    • Data sheet DS4311.

    Design Notes

    At 15 uH this part is in the middle of the family. The winding that produces that inductance is also what sets the 24.7 mOhm DCR - more turns, thinner wire, more resistance.

    The loss budget is the whole story with a power inductor: core loss grows with frequency and flux swing, copper loss grows with current, and the two meet at a different point for every inductance in the series.

    Frequently Asked Questions

    How much isolation is there between windings?
    The data sheet states the winding-to-winding voltage for each family. Treat it as a functional rating, not as reinforced insulation for a mains barrier.

    How much isolation is there between windings?
    The data sheet states the winding-to-winding voltage for each family. Treat it as a functional rating, not as reinforced insulation for a mains barrier.

    What is the OCL in parallel mode?
    With the windings paralleled the effective inductance is a quarter of the single-winding OCL; the datasheet lists the parallel rating explicitly.

    Design note: decide the connection before you lay out the board. Parallel, series and coupled all use the same part, and the inductance moves by 4x between them.

    Mechanical Dimensions

    eaton-drq-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message