Eaton DRQ127-1R0-R 1:1 Coupled Drum Core, 1 uH
Eaton DRQ127-1R0-R 1:1 Coupled Drum Core, 1 uH

Eaton DRQ127-1R0-R 1:1 Coupled Drum Core, 1 uH

Share
Eaton DRQ127-1R0-R: Dual Winding Shielded Drum Core Inductor, 1 uH, 15.5 A, DCR 2.61 mOhm.
    • Product Details
    • Download

    Eaton DRQ127-1R0-R 1:1 Coupled Drum Core, 1 uH

    DRQ127-1R0-R at a glance: dual-winding shielded drum core, 1 uH per winding, 15.5 A, DCR 2.61 mOhm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberDRQ127-1R0-R
    Rated inductance1 uH ±20%
    Open circuit inductance (OCL)0.82 uH
    Irms (40 °C rise)15.5 A
    Isat40 A
    DCR typical @ 20 °C2.61 mOhm
    Volt-microsecond rating4.9 V-us
    Series connection3.28 uH, 7.74 A
    Parallel connection1 uH, 15.5 A
    Turns ratio1:1, coupled
    Package12.5 x 12.5 mm footprint, 8.0 mm max height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    The Figures Explained

    One core, two windings, three possible connections. Parallel for current, series for inductance, or coupled as a transformer. The electrical ratings change by roughly a factor of four between the two extreme connections, so the connection is a design decision, not a wiring detail.

    The arithmetic is the usual one for coupled windings: parallel gives L/4 with 2x the current capability, series gives 4L with half. DCR follows the same rule - parallel halves the resistance, series doubles it.

    The saturation current is measured at a defined roll-off, and Eaton states the percentage on the data sheet: Isat is the peak current for approximately 30% rolloff at +20 °C. Read the number with the percentage in hand, because "saturation" means different things at 25% and at 40%.

    What This Family Is For

    DRQ127 is the tallest dual-winding DRQ at 8.0 mm and the highest-current part in the family, up to 56 A peak in parallel mode. Two windings, one core, and the option to use it as a transformer.

    • Typical applications: High current DC-DC, server power, SEPIC and flyback, battery systems, filter chokes.
    • The parallel rating is not double the single-winding rating of the same size - check both windings' DCR and the thermal path before assuming it.
    • Data sheet DS4311.

    Sizing It Into a Design

    At 1 uH this part is in the middle of the family. The winding that produces that inductance is also what sets the 2.61 mOhm DCR - more turns, thinner wire, more resistance.

    Efficiency is set by where you sit on the loss curve, and the curve moves with switching frequency. A part that is excellent at 300 kHz can be mediocre at 1 MHz with the same current, because the core loss term takes over.

    Frequently Asked Questions

    Can I use it as a flyback transformer?
    Yes, within the isolation and the 1:1 ratio. Check the reflected voltage and the leakage inductance, because leakage is what creates the spike on the switch node.

    Which connection do I use?
    Parallel for a high-current single inductor, series for high inductance at lower current, and coupled when you are building a SEPIC, flyback or a ripple-cancelling multiphase stage.

    Which connection do I use?
    Parallel for a high-current single inductor, series for high inductance at lower current, and coupled when you are building a SEPIC, flyback or a ripple-cancelling multiphase stage.

    Design note: decide the connection before you lay out the board. Parallel, series and coupled all use the same part, and the inductance moves by 4x between them.

    Mechanical Dimensions

    eaton-drq-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products