Eaton DRQ127-681-R 1:1 Coupled Drum Core, 680 uH
Eaton DRQ127-681-R 1:1 Coupled Drum Core, 680 uH

Eaton DRQ127-681-R 1:1 Coupled Drum Core, 680 uH

Share
Eaton DRQ127-681-R: Dual Winding Shielded Drum Core Inductor, 680 uH, 0.76 A, DCR 1.08 ohm.
    • Product Details
    • Download

    Eaton DRQ127-681-R 1:1 Coupled Drum Core, 680 uH

    DRQ127-681-R at a glance: dual-winding shielded drum core, 680 uH per winding, 0.76 A, DCR 1080 mOhm.

    Key Specifications

    ParameterValue
    Orderable part numberDRQ127-681-R
    Rated inductance680 uH ±20%
    Open circuit inductance (OCL)677 uH
    Irms (40 °C rise)0.76 A
    Isat1.39 A
    DCR typical @ 20 °C1080 mOhm
    Volt-microsecond rating141 V-us
    Series connection2707 uH, 0.38 A
    Parallel connection680 uH, 0.76 A
    Turns ratio1:1, coupled
    Package12.5 x 12.5 mm footprint, 8.0 mm max height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    Two windings on one core, and that is the whole idea: wire them in parallel and you get a high-current choke with a quarter of the inductance; wire them in series and you get four times the inductance at half the current. Same part, two very different components.

    Coupled operation is where the part earns its keep: with the right duty cycle the two windings cancel part of the ripple, so the output capacitor sees less AC current and the converter can run at a lower switching frequency for the same ripple.

    Saturation degrades with temperature on ferrite. Isat is the peak current for approximately 30% rolloff at +20 °C, and the hot value is the one that matters under a hood or inside a sealed enclosure.

    Series Positioning

    DRQ127 is the tallest dual-winding DRQ at 8.0 mm and the highest-current part in the family, up to 56 A peak in parallel mode. Two windings, one core, and the option to use it as a transformer.

    • Typical applications: High current DC-DC, server power, SEPIC and flyback, battery systems, filter chokes.
    • The parallel rating is not double the single-winding rating of the same size - check both windings' DCR and the thermal path before assuming it.
    • Data sheet DS4311.

    Sizing and Layout Notes

    Choose 680 uH when the ripple target is in the middle of the design window: the DCR stays at 1080 mOhm and the saturation limit at 1.39 A leaves the transient room it needs.

    Thermal design is not optional here. The rated current assumes a 40 °C rise with the part in free air on a stated pad; inside a closed box, on a thin board, next to a hot IC, that assumption is gone.

    Frequently Asked Questions

    What is the OCL in parallel mode?
    With the windings paralleled the effective inductance is a quarter of the single-winding OCL; the datasheet lists the parallel rating explicitly.

    How much isolation is there between windings?
    The data sheet states the winding-to-winding voltage for each family. Treat it as a functional rating, not as reinforced insulation for a mains barrier.

    Can I use it as a flyback transformer?
    Yes, within the isolation and the 1:1 ratio. Check the reflected voltage and the leakage inductance, because leakage is what creates the spike on the switch node.

    Design note: decide the connection before you lay out the board. Parallel, series and coupled all use the same part, and the inductance moves by 4x between them.

    Mechanical Dimensions

    eaton-drq-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products