Eaton DRQ73-1R5-R 1.5 uH Coupled Drum Core Inductor
Eaton DRQ73-1R5-R 1.5 uH Coupled Drum Core Inductor

Eaton DRQ73-1R5-R 1.5 uH Coupled Drum Core Inductor

Share
Eaton DRQ73-1R5-R: Dual Winding Shielded Drum Core Inductor, 1.5 uH, 4.64 A, DCR 13.2 mOhm.
    • Product Details
    • Download

    Eaton DRQ73-1R5-R 1.5 uH Coupled Drum Core Inductor

    DRQ73-1R5-R at a glance: dual-winding shielded drum core, 1.5 uH per winding, 4.64 A, DCR 13.2 mOhm.

    Electrical Specifications

    ParameterValue
    Orderable part numberDRQ73-1R5-R
    Rated inductance1.5 uH ±20%
    Open circuit inductance (OCL)1.48 uH
    Irms (40 °C rise)4.64 A
    Isat6.52 A
    DCR typical @ 20 °C13.2 mOhm
    Volt-microsecond rating4.36 V-us
    Series connection5.93 uH, 2.32 A
    Parallel connection1.5 uH, 4.64 A
    Turns ratio1:1, coupled
    Package7.6 x 7.6 mm footprint, 3.55 mm max height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    The Figures Explained

    One core, two windings, three possible connections. Parallel for current, series for inductance, or coupled as a transformer. The electrical ratings change by roughly a factor of four between the two extreme connections, so the connection is a design decision, not a wiring detail.

    The arithmetic is the usual one for coupled windings: parallel gives L/4 with 2x the current capability, series gives 4L with half. DCR follows the same rule - parallel halves the resistance, series doubles it.

    Saturation degrades with temperature on ferrite. Isat is the peak current for approximately 30% rolloff at +20 °C, and the hot value is the one that matters under a hood or inside a sealed enclosure.

    Series Positioning

    DRQ73 is a dual-winding drum core: two identical windings on one core that can be wired in parallel for a low-inductance high-current choke, in series for four times the inductance, or used as a 1:1 coupled inductor or transformer. Same 7.6 mm pad as the single-winding DR73.

    • Typical applications: Buck and boost stages, SEPIC and flyback transformers, output filters, LCD panels, portable devices.
    • The two windings are isolated to 200 Vac only - this is a functional barrier for circuit reasons, not a safety isolation rating.
    • Data sheet DS4311.

    Putting It to Work

    1.5 uH sits in the middle of the range, and the trade at that point is explicit: 13.2 mOhm of DCR against 6.52 A of saturation headroom.

    The loss budget is the whole story with a power inductor: core loss grows with frequency and flux swing, copper loss grows with current, and the two meet at a different point for every inductance in the series.

    Frequently Asked Questions

    How much isolation is there between windings?
    The data sheet states the winding-to-winding voltage for each family. Treat it as a functional rating, not as reinforced insulation for a mains barrier.

    What happens if I only use one winding?
    The part works as a single inductor, but the unused winding still occupies the core window - you do not get extra saturation headroom by leaving it open.

    Which connection do I use?
    Parallel for a high-current single inductor, series for high inductance at lower current, and coupled when you are building a SEPIC, flyback or a ripple-cancelling multiphase stage.

    Design note: decide the connection before you lay out the board. Parallel, series and coupled all use the same part, and the inductance moves by 4x between them.

    Mechanical Dimensions

    eaton-drq-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products