Eaton DRQ73-2R2-R 1:1 Coupled Drum Core, 2.2 uH
Eaton DRQ73-2R2-R 1:1 Coupled Drum Core, 2.2 uH

Eaton DRQ73-2R2-R 1:1 Coupled Drum Core, 2.2 uH

Share
Eaton DRQ73-2R2-R: Dual Winding Shielded Drum Core Inductor, 2.2 uH, 4.11 A, DCR 16.7 mOhm.
    • Product Details
    • Download

    Eaton DRQ73-2R2-R 1:1 Coupled Drum Core, 2.2 uH

    DRQ73-2R2-R at a glance: dual-winding shielded drum core, 2.2 uH per winding, 4.11 A, DCR 16.7 mOhm.

    Electrical Specifications

    ParameterValue
    Orderable part numberDRQ73-2R2-R
    Rated inductance2.2 uH ±20%
    Open circuit inductance (OCL)2.07 uH
    Irms (40 °C rise)4.11 A
    Isat5.52 A
    DCR typical @ 20 °C16.7 mOhm
    Volt-microsecond rating5.15 V-us
    Series connection8.28 uH, 2.06 A
    Parallel connection2.2 uH, 4.11 A
    Turns ratio1:1, coupled
    Package7.6 x 7.6 mm footprint, 3.55 mm max height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    The Figures Explained

    One core, two windings, three possible connections. Parallel for current, series for inductance, or coupled as a transformer. The electrical ratings change by roughly a factor of four between the two extreme connections, so the connection is a design decision, not a wiring detail.

    Coupled operation is where the part earns its keep: with the right duty cycle the two windings cancel part of the ripple, so the output capacitor sees less AC current and the converter can run at a lower switching frequency for the same ripple.

    Saturation degrades with temperature on ferrite. Isat is the peak current for approximately 30% rolloff at +20 °C, and the hot value is the one that matters under a hood or inside a sealed enclosure.

    What This Family Is For

    DRQ73 is a dual-winding drum core: two identical windings on one core that can be wired in parallel for a low-inductance high-current choke, in series for four times the inductance, or used as a 1:1 coupled inductor or transformer. Same 7.6 mm pad as the single-winding DR73.

    • Typical applications: Buck and boost stages, SEPIC and flyback transformers, output filters, LCD panels, portable devices.
    • The two windings are isolated to 200 Vac only - this is a functional barrier for circuit reasons, not a safety isolation rating.
    • Data sheet DS4311.

    Design Notes

    Choose 2.2 uH when the ripple target is in the middle of the design window: the DCR stays at 16.7 mOhm and the saturation limit at 5.52 A leaves the transient room it needs.

    The loss budget is the whole story with a power inductor: core loss grows with frequency and flux swing, copper loss grows with current, and the two meet at a different point for every inductance in the series.

    Frequently Asked Questions

    Does the coupling ratio matter?
    Yes. The turns ratio is 1:1, and the ripple cancellation depends on it. A part with a different ratio is not interchangeable in a coupled design.

    Can I use it as a flyback transformer?
    Yes, within the isolation and the 1:1 ratio. Check the reflected voltage and the leakage inductance, because leakage is what creates the spike on the switch node.

    Does the coupling ratio matter?
    Yes. The turns ratio is 1:1, and the ripple cancellation depends on it. A part with a different ratio is not interchangeable in a coupled design.

    Design note: decide the connection before you lay out the board. Parallel, series and coupled all use the same part, and the inductance moves by 4x between them.

    Mechanical Dimensions

    eaton-drq-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products