Eaton DRQ73-3R3-R - Dual Winding 3.3 uH Power Inductor
Eaton DRQ73-3R3-R - Dual Winding 3.3 uH Power Inductor

Eaton DRQ73-3R3-R - Dual Winding 3.3 uH Power Inductor

Share
Eaton DRQ73-3R3-R: Dual Winding Shielded Drum Core Inductor, 3.3 uH, 3.31 A, DCR 25.9 mOhm.
    • Product Details
    • Download

    Eaton DRQ73-3R3-R - Dual Winding 3.3 uH Power Inductor

    DRQ73-3R3-R at a glance: dual-winding shielded drum core, 3.3 uH per winding, 3.31 A, DCR 25.9 mOhm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberDRQ73-3R3-R
    Rated inductance3.3 uH ±20%
    Open circuit inductance (OCL)3.54 uH
    Irms (40 °C rise)3.31 A
    Isat4.22 A
    DCR typical @ 20 °C25.9 mOhm
    Volt-microsecond rating6.73 V-us
    Series connection14.2 uH, 1.66 A
    Parallel connection3.3 uH, 3.31 A
    Turns ratio1:1, coupled
    Package7.6 x 7.6 mm footprint, 3.55 mm max height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    The Figures Explained

    The DRQ/DRAQ construction puts two windings on a shielded drum core with a defined 1:1 turns ratio. That ratio is what makes the part useful as a transformer: the two windings share flux, so the magnetising current is common and the ripple can be made to cancel.

    The arithmetic is the usual one for coupled windings: parallel gives L/4 with 2x the current capability, series gives 4L with half. DCR follows the same rule - parallel halves the resistance, series doubles it.

    Saturation degrades with temperature on ferrite. Isat is the peak current for approximately 30% rolloff at +20 °C, and the hot value is the one that matters under a hood or inside a sealed enclosure.

    Series Positioning

    DRQ73 is a dual-winding drum core: two identical windings on one core that can be wired in parallel for a low-inductance high-current choke, in series for four times the inductance, or used as a 1:1 coupled inductor or transformer. Same 7.6 mm pad as the single-winding DR73.

    • Typical applications: Buck and boost stages, SEPIC and flyback transformers, output filters, LCD panels, portable devices.
    • The two windings are isolated to 200 Vac only - this is a functional barrier for circuit reasons, not a safety isolation rating.
    • Data sheet DS4311.

    Design Notes

    At 3.3 uH this part is in the middle of the family. The winding that produces that inductance is also what sets the 25.9 mOhm DCR - more turns, thinner wire, more resistance.

    The loss budget is the whole story with a power inductor: core loss grows with frequency and flux swing, copper loss grows with current, and the two meet at a different point for every inductance in the series.

    Frequently Asked Questions

    Can I use it as a flyback transformer?
    Yes, within the isolation and the 1:1 ratio. Check the reflected voltage and the leakage inductance, because leakage is what creates the spike on the switch node.

    How much isolation is there between windings?
    The data sheet states the winding-to-winding voltage for each family. Treat it as a functional rating, not as reinforced insulation for a mains barrier.

    What is the OCL in parallel mode?
    With the windings paralleled the effective inductance is a quarter of the single-winding OCL; the datasheet lists the parallel rating explicitly.

    Design note: decide the connection before you lay out the board. Parallel, series and coupled all use the same part, and the inductance moves by 4x between them.

    Mechanical Dimensions

    eaton-drq-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products