Eaton DRQ73-820-R 1:1 Coupled Drum Core, 82 uH
Eaton DRQ73-820-R 1:1 Coupled Drum Core, 82 uH

Eaton DRQ73-820-R 1:1 Coupled Drum Core, 82 uH

Share
Eaton DRQ73-820-R: Dual Winding Shielded Drum Core Inductor, 82 uH, 0.86 A, DCR 384 mOhm.
    • Product Details
    • Download

    Eaton DRQ73-820-R 1:1 Coupled Drum Core, 82 uH

    DRQ73-820-R at a glance: dual-winding shielded drum core, 82 uH per winding, 0.86 A, DCR 384 mOhm.

    Key Specifications

    ParameterValue
    Orderable part numberDRQ73-820-R
    Rated inductance82 uH ±20%
    Open circuit inductance (OCL)80.4 uH
    Irms (40 °C rise)0.86 A
    Isat0.89 A
    DCR typical @ 20 °C384 mOhm
    Volt-microsecond rating32.1 V-us
    Series connection322 uH, 0.43 A
    Parallel connection82 uH, 0.86 A
    Turns ratio1:1, coupled
    Package7.6 x 7.6 mm footprint, 3.55 mm max height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    One core, two windings, three possible connections. Parallel for current, series for inductance, or coupled as a transformer. The electrical ratings change by roughly a factor of four between the two extreme connections, so the connection is a design decision, not a wiring detail.

    In parallel mode the two windings share the current and the DCR drops by half, which is why the parallel rating is roughly twice the single-winding rating rather than exactly twice: the thermal path is the same core.

    The saturation current is measured at a defined roll-off, and Eaton states the percentage on the data sheet: Isat is the peak current for approximately 30% rolloff at +20 °C. Read the number with the percentage in hand, because "saturation" means different things at 25% and at 40%.

    Positioning in the Range

    DRQ73 is a dual-winding drum core: two identical windings on one core that can be wired in parallel for a low-inductance high-current choke, in series for four times the inductance, or used as a 1:1 coupled inductor or transformer. Same 7.6 mm pad as the single-winding DR73.

    • Typical applications: Buck and boost stages, SEPIC and flyback transformers, output filters, LCD panels, portable devices.
    • The two windings are isolated to 200 Vac only - this is a functional barrier for circuit reasons, not a safety isolation rating.
    • Data sheet DS4311.

    Design Notes

    82 uH is in the middle of what this series covers. Moving up in inductance costs DCR and saturation current; moving down buys both, at the price of ripple.

    Thermal design is not optional here. The rated current assumes a 40 °C rise with the part in free air on a stated pad; inside a closed box, on a thin board, next to a hot IC, that assumption is gone.

    Frequently Asked Questions

    What is the OCL in parallel mode?
    With the windings paralleled the effective inductance is a quarter of the single-winding OCL; the datasheet lists the parallel rating explicitly.

    Can I use it as a flyback transformer?
    Yes, within the isolation and the 1:1 ratio. Check the reflected voltage and the leakage inductance, because leakage is what creates the spike on the switch node.

    Does the coupling ratio matter?
    Yes. The turns ratio is 1:1, and the ripple cancellation depends on it. A part with a different ratio is not interchangeable in a coupled design.

    Design note: decide the connection before you lay out the board. Parallel, series and coupled all use the same part, and the inductance moves by 4x between them.

    Mechanical Dimensions

    eaton-drq-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products