Eaton DRQ74-151-R - Dual Winding 150 uH Power Inductor
Eaton DRQ74-151-R - Dual Winding 150 uH Power Inductor

Eaton DRQ74-151-R - Dual Winding 150 uH Power Inductor

Share
Eaton DRQ74-151-R: Dual Winding Shielded Drum Core Inductor, 150 uH, 0.69 A, DCR 591 mOhm.
    • Product Details
    • Download

    Eaton DRQ74-151-R - Dual Winding 150 uH Power Inductor

    DRQ74-151-R at a glance: dual-winding shielded drum core, 150 uH per winding, 0.69 A, DCR 591 mOhm.

    Electrical Specifications

    ParameterValue
    Orderable part numberDRQ74-151-R
    Rated inductance150 uH ±20%
    Open circuit inductance (OCL)150 uH
    Irms (40 °C rise)0.69 A
    Isat0.81 A
    DCR typical @ 20 °C591 mOhm
    Volt-microsecond rating38.6 V-us
    Series connection600 uH, 0.35 A
    Parallel connection150 uH, 0.69 A
    Turns ratio1:1, coupled
    Package7.6 x 7.6 mm footprint, 4.35 mm max height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    One core, two windings, three possible connections. Parallel for current, series for inductance, or coupled as a transformer. The electrical ratings change by roughly a factor of four between the two extreme connections, so the connection is a design decision, not a wiring detail.

    In parallel mode the two windings share the current and the DCR drops by half, which is why the parallel rating is roughly twice the single-winding rating rather than exactly twice: the thermal path is the same core.

    Isat is the peak current for approximately 30% rolloff at +20 °C. In a buck converter the inductor current peaks at the top of the ripple, so the peak - not the average - is the number that has to stay below Isat with margin for the transient.

    What This Family Is For

    DRQ74 is the taller of the two 7.6 mm dual-winding parts at 4.35 mm, so it carries more current than DRQ73 in the same footprint. Two windings, series or parallel, 1:1 coupling when you want a transformer instead of a choke.

    • Typical applications: Multi-output converters, SEPIC and flyback, filter chokes, portable power, LCD backlighting.
    • Series connection gives 4x the inductance and half the current rating; parallel gives a quarter of the inductance and twice the current. Neither is a free lunch.
    • Data sheet DS4311.

    Putting It to Work

    At 150 uH this part is in the middle of the family. The winding that produces that inductance is also what sets the 591 mOhm DCR - more turns, thinner wire, more resistance.

    Thermal design is not optional here. The rated current assumes a 40 °C rise with the part in free air on a stated pad; inside a closed box, on a thin board, next to a hot IC, that assumption is gone.

    Frequently Asked Questions

    What happens if I only use one winding?
    The part works as a single inductor, but the unused winding still occupies the core window - you do not get extra saturation headroom by leaving it open.

    What happens if I only use one winding?
    The part works as a single inductor, but the unused winding still occupies the core window - you do not get extra saturation headroom by leaving it open.

    Does the coupling ratio matter?
    Yes. The turns ratio is 1:1, and the ripple cancellation depends on it. A part with a different ratio is not interchangeable in a coupled design.

    Design note: decide the connection before you lay out the board. Parallel, series and coupled all use the same part, and the inductance moves by 4x between them.

    Mechanical Dimensions

    eaton-drq-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message