Eaton DRQ74-1R0-R Shielded Coupled Inductor 1 uH 5.33 A
Eaton DRQ74-1R0-R Shielded Coupled Inductor 1 uH 5.33 A

Eaton DRQ74-1R0-R Shielded Coupled Inductor 1 uH 5.33 A

Share
Eaton DRQ74-1R0-R: Dual Winding Shielded Drum Core Inductor, 1 uH, 5.33 A, DCR 10 mOhm.
    • Product Details
    • Download

    Eaton DRQ74-1R0-R Shielded Coupled Inductor 1 uH 5.33 A

    DRQ74-1R0-R at a glance: dual-winding shielded drum core, 1 uH per winding, 5.33 A, DCR 10 mOhm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberDRQ74-1R0-R
    Rated inductance1 uH ±20%
    Open circuit inductance (OCL)0.95 uH
    Irms (40 °C rise)5.33 A
    Isat10.2 A
    DCR typical @ 20 °C10 mOhm
    Volt-microsecond rating3.08 V-us
    Series connection3.81 uH, 2.66 A
    Parallel connection1 uH, 5.33 A
    Turns ratio1:1, coupled
    Package7.6 x 7.6 mm footprint, 4.35 mm max height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    Two windings on one core, and that is the whole idea: wire them in parallel and you get a high-current choke with a quarter of the inductance; wire them in series and you get four times the inductance at half the current. Same part, two very different components.

    Series mode is often mistaken for a way to get more current. It is the opposite - four times the inductance, half the saturation current, twice the DCR. Use it when you need inductance, not when you need amps.

    The saturation current is measured at a defined roll-off, and Eaton states the percentage on the data sheet: Isat is the peak current for approximately 30% rolloff at +20 °C. Read the number with the percentage in hand, because "saturation" means different things at 25% and at 40%.

    Where This Series Fits

    DRQ74 is the taller of the two 7.6 mm dual-winding parts at 4.35 mm, so it carries more current than DRQ73 in the same footprint. Two windings, series or parallel, 1:1 coupling when you want a transformer instead of a choke.

    • Typical applications: Multi-output converters, SEPIC and flyback, filter chokes, portable power, LCD backlighting.
    • Series connection gives 4x the inductance and half the current rating; parallel gives a quarter of the inductance and twice the current. Neither is a free lunch.
    • Data sheet DS4311.

    Design Notes

    Choose 1 uH when the ripple target is in the middle of the design window: the DCR stays at 10 mOhm and the saturation limit at 10.2 A leaves the transient room it needs.

    Thermal design is not optional here. The rated current assumes a 40 °C rise with the part in free air on a stated pad; inside a closed box, on a thin board, next to a hot IC, that assumption is gone.

    Frequently Asked Questions

    What is the OCL in parallel mode?
    With the windings paralleled the effective inductance is a quarter of the single-winding OCL; the datasheet lists the parallel rating explicitly.

    Can I use it as a flyback transformer?
    Yes, within the isolation and the 1:1 ratio. Check the reflected voltage and the leakage inductance, because leakage is what creates the spike on the switch node.

    What happens if I only use one winding?
    The part works as a single inductor, but the unused winding still occupies the core window - you do not get extra saturation headroom by leaving it open.

    Design note: decide the connection before you lay out the board. Parallel, series and coupled all use the same part, and the inductance moves by 4x between them.

    Mechanical Dimensions

    eaton-drq-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products