Eaton DRQ74-331-R 1:1 Coupled Drum Core, 330 uH
Eaton DRQ74-331-R 1:1 Coupled Drum Core, 330 uH

Eaton DRQ74-331-R 1:1 Coupled Drum Core, 330 uH

Share
Eaton DRQ74-331-R: Dual Winding Shielded Drum Core Inductor, 330 uH, 0.45 A, DCR 1.41 ohm.
    • Product Details
    • Download

    Eaton DRQ74-331-R 1:1 Coupled Drum Core, 330 uH

    DRQ74-331-R at a glance: dual-winding shielded drum core, 330 uH per winding, 0.45 A, DCR 1410 mOhm.

    Key Specifications

    ParameterValue
    Orderable part numberDRQ74-331-R
    Rated inductance330 uH ±20%
    Open circuit inductance (OCL)336 uH
    Irms (40 °C rise)0.45 A
    Isat0.54 A
    DCR typical @ 20 °C1410 mOhm
    Volt-microsecond rating57.8 V-us
    Series connection1342 uH, 0.22 A
    Parallel connection330 uH, 0.45 A
    Turns ratio1:1, coupled
    Package7.6 x 7.6 mm footprint, 4.35 mm max height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    How to Read These Ratings

    Two windings on one core, and that is the whole idea: wire them in parallel and you get a high-current choke with a quarter of the inductance; wire them in series and you get four times the inductance at half the current. Same part, two very different components.

    Series mode is often mistaken for a way to get more current. It is the opposite - four times the inductance, half the saturation current, twice the DCR. Use it when you need inductance, not when you need amps.

    Saturation degrades with temperature on ferrite. Isat is the peak current for approximately 30% rolloff at +20 °C, and the hot value is the one that matters under a hood or inside a sealed enclosure.

    Where This Series Fits

    DRQ74 is the taller of the two 7.6 mm dual-winding parts at 4.35 mm, so it carries more current than DRQ73 in the same footprint. Two windings, series or parallel, 1:1 coupling when you want a transformer instead of a choke.

    • Typical applications: Multi-output converters, SEPIC and flyback, filter chokes, portable power, LCD backlighting.
    • Series connection gives 4x the inductance and half the current rating; parallel gives a quarter of the inductance and twice the current. Neither is a free lunch.
    • Data sheet DS4311.

    Putting It to Work

    Choose 330 uH when the ripple target is in the middle of the design window: the DCR stays at 1410 mOhm and the saturation limit at 0.54 A leaves the transient room it needs.

    Thermal design is not optional here. The rated current assumes a 40 °C rise with the part in free air on a stated pad; inside a closed box, on a thin board, next to a hot IC, that assumption is gone.

    Frequently Asked Questions

    Can I use it as a flyback transformer?
    Yes, within the isolation and the 1:1 ratio. Check the reflected voltage and the leakage inductance, because leakage is what creates the spike on the switch node.

    What happens if I only use one winding?
    The part works as a single inductor, but the unused winding still occupies the core window - you do not get extra saturation headroom by leaving it open.

    What is the OCL in parallel mode?
    With the windings paralleled the effective inductance is a quarter of the single-winding OCL; the datasheet lists the parallel rating explicitly.

    Design note: decide the connection before you lay out the board. Parallel, series and coupled all use the same part, and the inductance moves by 4x between them.

    Mechanical Dimensions

    eaton-drq-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products