Eaton DRQ74-4R7-R Shielded Coupled Inductor 4.7 uH 3.34 A
Eaton DRQ74-4R7-R Shielded Coupled Inductor 4.7 uH 3.34 A

Eaton DRQ74-4R7-R Shielded Coupled Inductor 4.7 uH 3.34 A

Share
Eaton DRQ74-4R7-R: Dual Winding Shielded Drum Core Inductor, 4.7 uH, 3.34 A, DCR 25.4 mOhm.
    • Product Details
    • Download

    Eaton DRQ74-4R7-R Shielded Coupled Inductor 4.7 uH 3.34 A

    DRQ74-4R7-R at a glance: dual-winding shielded drum core, 4.7 uH per winding, 3.34 A, DCR 25.4 mOhm.

    Electrical Specifications

    ParameterValue
    Orderable part numberDRQ74-4R7-R
    Rated inductance4.7 uH ±20%
    Open circuit inductance (OCL)5.18 uH
    Irms (40 °C rise)3.34 A
    Isat4.37 A
    DCR typical @ 20 °C25.4 mOhm
    Volt-microsecond rating7.18 V-us
    Series connection20.7 uH, 1.67 A
    Parallel connection4.7 uH, 3.34 A
    Turns ratio1:1, coupled
    Package7.6 x 7.6 mm footprint, 4.35 mm max height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    The Figures Explained

    One core, two windings, three possible connections. Parallel for current, series for inductance, or coupled as a transformer. The electrical ratings change by roughly a factor of four between the two extreme connections, so the connection is a design decision, not a wiring detail.

    Coupled operation is where the part earns its keep: with the right duty cycle the two windings cancel part of the ripple, so the output capacitor sees less AC current and the converter can run at a lower switching frequency for the same ripple.

    Saturation degrades with temperature on ferrite. Isat is the peak current for approximately 30% rolloff at +20 °C, and the hot value is the one that matters under a hood or inside a sealed enclosure.

    Positioning in the Range

    DRQ74 is the taller of the two 7.6 mm dual-winding parts at 4.35 mm, so it carries more current than DRQ73 in the same footprint. Two windings, series or parallel, 1:1 coupling when you want a transformer instead of a choke.

    • Typical applications: Multi-output converters, SEPIC and flyback, filter chokes, portable power, LCD backlighting.
    • Series connection gives 4x the inductance and half the current rating; parallel gives a quarter of the inductance and twice the current. Neither is a free lunch.
    • Data sheet DS4311.

    Sizing It Into a Design

    4.7 uH is in the middle of what this series covers. Moving up in inductance costs DCR and saturation current; moving down buys both, at the price of ripple.

    Thermal design is not optional here. The rated current assumes a 40 °C rise with the part in free air on a stated pad; inside a closed box, on a thin board, next to a hot IC, that assumption is gone.

    Frequently Asked Questions

    Can I use it as a flyback transformer?
    Yes, within the isolation and the 1:1 ratio. Check the reflected voltage and the leakage inductance, because leakage is what creates the spike on the switch node.

    What happens if I only use one winding?
    The part works as a single inductor, but the unused winding still occupies the core window - you do not get extra saturation headroom by leaving it open.

    How much isolation is there between windings?
    The data sheet states the winding-to-winding voltage for each family. Treat it as a functional rating, not as reinforced insulation for a mains barrier.

    Design note: decide the connection before you lay out the board. Parallel, series and coupled all use the same part, and the inductance moves by 4x between them.

    Mechanical Dimensions

    eaton-drq-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products