Eaton DRQ74-680-R 1:1 Coupled Drum Core, 68 uH
Eaton DRQ74-680-R 1:1 Coupled Drum Core, 68 uH

Eaton DRQ74-680-R 1:1 Coupled Drum Core, 68 uH

Share
Eaton DRQ74-680-R: Dual Winding Shielded Drum Core Inductor, 68 uH, 1.03 A, DCR 265 mOhm.
    • Product Details
    • Download

    Eaton DRQ74-680-R 1:1 Coupled Drum Core, 68 uH

    DRQ74-680-R at a glance: dual-winding shielded drum core, 68 uH per winding, 1.03 A, DCR 265 mOhm.

    Specification Table

    ParameterValue
    Orderable part numberDRQ74-680-R
    Rated inductance68 uH ±20%
    Open circuit inductance (OCL)69.7 uH
    Irms (40 °C rise)1.03 A
    Isat1.19 A
    DCR typical @ 20 °C265 mOhm
    Volt-microsecond rating26.3 V-us
    Series connection279 uH, 0.52 A
    Parallel connection68 uH, 1.03 A
    Turns ratio1:1, coupled
    Package7.6 x 7.6 mm footprint, 4.35 mm max height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    The Figures Explained

    The DRQ/DRAQ construction puts two windings on a shielded drum core with a defined 1:1 turns ratio. That ratio is what makes the part useful as a transformer: the two windings share flux, so the magnetising current is common and the ripple can be made to cancel.

    The arithmetic is the usual one for coupled windings: parallel gives L/4 with 2x the current capability, series gives 4L with half. DCR follows the same rule - parallel halves the resistance, series doubles it.

    Saturation degrades with temperature on ferrite. Isat is the peak current for approximately 30% rolloff at +20 °C, and the hot value is the one that matters under a hood or inside a sealed enclosure.

    Where This Series Fits

    DRQ74 is the taller of the two 7.6 mm dual-winding parts at 4.35 mm, so it carries more current than DRQ73 in the same footprint. Two windings, series or parallel, 1:1 coupling when you want a transformer instead of a choke.

    • Typical applications: Multi-output converters, SEPIC and flyback, filter chokes, portable power, LCD backlighting.
    • Series connection gives 4x the inductance and half the current rating; parallel gives a quarter of the inductance and twice the current. Neither is a free lunch.
    • Data sheet DS4311.

    Sizing and Layout Notes

    68 uH sits in the middle of the range, and the trade at that point is explicit: 265 mOhm of DCR against 1.19 A of saturation headroom.

    Thermal design is not optional here. The rated current assumes a 40 °C rise with the part in free air on a stated pad; inside a closed box, on a thin board, next to a hot IC, that assumption is gone.

    Frequently Asked Questions

    Can I use it as a flyback transformer?
    Yes, within the isolation and the 1:1 ratio. Check the reflected voltage and the leakage inductance, because leakage is what creates the spike on the switch node.

    Can I use it as a flyback transformer?
    Yes, within the isolation and the 1:1 ratio. Check the reflected voltage and the leakage inductance, because leakage is what creates the spike on the switch node.

    What happens if I only use one winding?
    The part works as a single inductor, but the unused winding still occupies the core window - you do not get extra saturation headroom by leaving it open.

    Design note: decide the connection before you lay out the board. Parallel, series and coupled all use the same part, and the inductance moves by 4x between them.

    Mechanical Dimensions

    eaton-drq-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products