Eaton EXLA1V0606-8R2-R Automotive Molded Inductor 8.2 uH, 8 A Isat
Eaton EXLA1V0606-8R2-R Automotive Molded Inductor 8.2 uH, 8 A Isat

Eaton EXLA1V0606-8R2-R Automotive Molded Inductor 8.2 uH, 8 A Isat

Share
Eaton EXLA1V0606-8R2-R: AEC-Q200 Automotive Molded Power Inductor, 8.2 uH, 8 A, DCR 22.5 mOhm.
    • Product Details
    • Download

    Eaton EXLA1V0606-8R2-R Automotive Molded Inductor 8.2 uH, 8 A Isat

    EXLA1V0606-8R2-R at a glance: AEC-Q200 molded inductor, 8.2 uH, 8 A Irms, Isat 8 A, DCR 22.5 mOhm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberEXLA1V0606-8R2-R
    OCL8.2 uH ±20%
    Irms8 A
    Isat (30% rolloff @ +25 °C)8 A
    DCR typical @ +25 °C22.5 mOhm
    DCR maximum @ +25 °C24.8 mOhm
    Rated operating voltage (across inductor)15 V
    Package7.4 x 7.1 mm footprint, 6.0 mm height
    MountingSurface mount
    Operating temperature-55 °C to +155 °C
    QualificationAEC-Q200
    RoHSCompliant (-R suffix)

    Outline Drawing

    EXLA1V0606-8R2-R mechanical dimensions and pad layout

    Drawings from the Eaton data sheet: mechanical outline with rated mm dimensions, recommended PCB pad layout, and winding schematic. Tolerances and pad tolerances are stated on the drawing itself.

    The Figures Explained

    Between the battery and the load sits a rail that must survive cranking transients, thermal cycling and vibration. This AEC-Q200 moulded inductor is built for that point in the circuit: high current, low DCR, and a saturation curve that degrades gracefully.

    Copper loss is the efficiency floor. 22.5 mOhm at 25 °C rises about 30% by 100 °C, so the hot-corner budget should use the maximum column, not the typical.

    Saturation on a powder core is a curve, not a cliff: Isat is the peak current for approximately 30% rolloff at +25 °C, and beyond it the inductance continues to fall smoothly. Budget the transient peak against the inductance you actually need, not against the part surviving.

    The 155 °C rating is ambient plus self-heating, and the alloy powder core keeps its soft-saturation shape across that range - the transient behaviour at the hot corner is a milder version of the room-temperature curve, not a different part.

    Where This Series Fits

    EXLA is the automotive moulded family: AEC-Q200 qualified, soft-saturating, shielded, rated to 155 °C - the power-inductor choice for ADAS, body electronics and infotainment rails.

    • Typical applications: ADAS power rails, body electronics, infotainment, zonal modules and other automotive DC-DC stages.
    • Automotive derating practice: size against Isat and the hot DCR at the worst ambient, with margin for the load transient.
    • Data sheet ELX1221; footprint 7.4 x 7.1 mm footprint, 6.0 mm height.

    Sizing and Layout Notes

    Frequently Asked Questions

    What is the temperature range?
    -55 °C to +155 °C, ambient plus self-temperature rise. The part should not exceed +155 °C under worst-case operating conditions.

    Is this AEC-Q200 qualified?
    Yes - the family is qualified to the automotive passive-component standard, including the terminal-strength and vibration test methods referenced on the datasheet.

    What is the temperature range?
    -55 °C to +155 °C, ambient plus self-temperature rise. The part should not exceed +155 °C under worst-case operating conditions.

    Design note: budget the loss at the hot corner with the maximum DCR, and keep the transient peak below Isat with margin - the soft curve forgives, but does not eliminate, saturation.

    Mechanical Dimensions

    eaton-exla1v06-automotive-high-current-molded-inductor-data-sheet-elx1221-en mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products