Eaton EXLA1V1006-5R6-R Automotive Molded Power Inductor 5.6 uH
Eaton EXLA1V1006-5R6-R Automotive Molded Power Inductor 5.6 uH

Eaton EXLA1V1006-5R6-R Automotive Molded Power Inductor 5.6 uH

Share
Eaton EXLA1V1006-5R6-R: AEC-Q200 Automotive Molded Power Inductor, 5.6 uH, 12 A, DCR 10.8 mOhm.
    • Product Details
    • Download

    Eaton EXLA1V1006-5R6-R Automotive Molded Power Inductor 5.6 uH

    EXLA1V1006-5R6-R at a glance: AEC-Q200 molded inductor, 5.6 uH, 12 A Irms, Isat 17 A, DCR 10.8 mOhm.

    Key Specifications

    ParameterValue
    Orderable part numberEXLA1V1006-5R6-R
    OCL5.6 uH ±20%
    Irms12 A
    Isat (30% rolloff @ +25 °C)17 A
    DCR typical @ +25 °C10.8 mOhm
    DCR maximum @ +25 °C11.9 mOhm
    Rated operating voltage (across inductor)40 V
    Package12.2 x 11.3 mm footprint, 6.0 mm height
    MountingSurface mount
    Operating temperature-55 °C to +155 °C
    QualificationAEC-Q200
    RoHSCompliant (-R suffix)

    Mechanical Dimensions & Pad Layout

    EXLA1V1006-5R6-R mechanical dimensions and pad layout

    Drawings from the Eaton data sheet: mechanical outline with rated mm dimensions, recommended PCB pad layout, and winding schematic. Tolerances and pad tolerances are stated on the drawing itself.

    Reading the Data Sheet

    Between the battery and the load sits a rail that must survive cranking transients, thermal cycling and vibration. This AEC-Q200 moulded inductor is built for that point in the circuit: high current, low DCR, and a saturation curve that degrades gracefully.

    At 10.8 mOhm the winding dominates the loss budget at load. The moulded construction spreads that heat into the body, but the board the part sits on still decides the actual temperature rise.

    Isat is the peak current for approximately 30% rolloff at +25 °C. In a multiphase converter the transient peak lands on the inductors before the loop corrects; a soft-saturating core keeps controlling di/dt through exactly that window.

    The 155 °C rating is ambient plus self-heating, and the alloy powder core keeps its soft-saturation shape across that range - the transient behaviour at the hot corner is a milder version of the room-temperature curve, not a different part.

    Series Positioning

    EXLA is the automotive moulded family: AEC-Q200 qualified, soft-saturating, shielded, rated to 155 °C - the power-inductor choice for ADAS, body electronics and infotainment rails.

    • Typical applications: ADAS power rails, body electronics, infotainment, zonal modules and other automotive DC-DC stages.
    • Automotive derating practice: size against Isat and the hot DCR at the worst ambient, with margin for the load transient.
    • Data sheet ELX1251; footprint 12.2 x 11.3 mm footprint, 6.0 mm height.

    Design Notes

    Frequently Asked Questions

    Is this AEC-Q200 qualified?
    Yes - the family is qualified to the automotive passive-component standard, including the terminal-strength and vibration test methods referenced on the datasheet.

    What is the temperature range?
    -55 °C to +155 °C, ambient plus self-temperature rise. The part should not exceed +155 °C under worst-case operating conditions.

    Is this AEC-Q200 qualified?
    Yes - the family is qualified to the automotive passive-component standard, including the terminal-strength and vibration test methods referenced on the datasheet.

    Design note: budget the loss at the hot corner with the maximum DCR, and keep the transient peak below Isat with margin - the soft curve forgives, but does not eliminate, saturation.

    Mechanical Dimensions

    eaton-exla1v10-automotive-high-current-molded-inductor-data-sheet-elx1251-en mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products