Eaton FP0404R1-R100-R 40 A SMD Power Inductor, 100 nH
Eaton FP0404R1-R100-R 40 A SMD Power Inductor, 100 nH

Eaton FP0404R1-R100-R 40 A SMD Power Inductor, 100 nH

Share
pEaton FP0404R1-R100-R: 100 nH high frequency, high current power inductor, 40 A Irms, 15.6 A Isat, DCR 0.32 mOhm, 4.0 x 4.0 mm package./p
    • Product Details
    • Download

    FP0404R1-R100-R at a glance: 100 nH high frequency, high current power inductor, 40 A Irms, 15.6 A Isat, DCR 0.32 mOhm, 4.0 x 4.0 mm body, 3.0 mm or 4.0 mm tall.

    Eaton FP0404R1-R100-R High frequency, high current power inductors

    FP0404R1-R100-R is one of Eaton's high frequency, high current power inductor series, 4.0 x 4.0 mm with a 3.0 mm or 4.0 mm tall profile. Electrically it offers 100 nH at 40 A Irms and 0.32 mOhm typical DCR, which is the combination you want when the rail carries tens of amps and the board has no room for a larger can.

    Specification Table

    Orderable part numberFP0404R1-R100-R
    Inductance, OCL (0 Adc)100 nH
    Inductance, FLL (minimum)68 nH
    Irms (40 °C rise, no core loss)40 A
    Isat (20% roll-off @ +25 °C)15.6 A
    Isat2 (20% roll-off @ +100 °C)14 A
    Isat3 (20% roll-off @ +125 °C)13 A
    DCR typical @ +20 °C0.32 mOhm
    K-factor (Bp-p = K x L x dI)2,248
    Package4.0 x 4.0 mm, 3.0 mm / 4.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    Moisture sensitivity levelMSL 1
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    At zero bias the winding measures 100 nH. Put Isat1 through it and the figure falls to 68 nH, about 32% lower, because the ferrite is partly saturated. Ripple calculations belong on the 100 nH number; loop stability and worst-case current belong on the lower one.

    Peak current at 20% roll-off is 15.6 A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.

    The 512 mW dissipated at 40 A through 0.32 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.

    The K-factor of 2,248 turns ripple into flux: a peak-to-peak swing of 4.68 A gives about 105.2 mT peak in the core. Read the material loss curve at that flux and your switching frequency to get the loss term Irms leaves out.

    Series Positioning

    This is one of the smaller bodies in the FP range. At 4.0 x 4.0 mm it is meant for point-of-load stages and multi-phase VRMs where board area is the binding constraint and current per phase is tens of amps rather than hundreds. At 100 nH this is a low-inductance point for the family, which means high ripple for a given input voltage and duty cycle. That is the intent: these parts are chosen when the converter switches fast and the inductor shapes the ripple rather than storing bulk energy.

    That makes it part 4 of 6 when the data sheet is sorted by inductance.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs), Server and desktop VRMs and EVRDs.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Putting It to Work

    Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 100 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.32 mOhm the winding is not the loss, the trace can be.

    Dimensions and Pad Layout

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP0404R1-R100-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Is this part AEC-Q200 qualified?
    No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.

    Can I substitute a lower inductance in the same body?
    Only after checking saturation. Lower inductance means higher ripple and a higher peak current for the same DC load. The part with less inductance usually has more saturation headroom, but the ripple penalty is real, so recalculate peak current before substituting.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products