Eaton FP0404R1-R110-R 110 nH 14.2 A Saturation Inductor
Eaton FP0404R1-R110-R 110 nH 14.2 A Saturation Inductor

Eaton FP0404R1-R110-R 110 nH 14.2 A Saturation Inductor

Share
pEaton FP0404R1-R110-R: 110 nH high frequency, high current power inductor, 40 A Irms, 14.2 A Isat, DCR 0.32 mOhm, 4.0 x 4.0 mm package./p
    • Product Details
    • Download

    FP0404R1-R110-R at a glance: 110 nH high frequency, high current power inductor, 40 A Irms, 14.2 A Isat, DCR 0.32 mOhm, 4.0 x 4.0 mm body, 3.0 mm or 4.0 mm tall.

    Eaton FP0404R1-R110-R High frequency, high current power inductors

    The FP0404R1-R110-R is a 4.0 x 4.0 mm high frequency, high current power inductor from Eaton, rated 40 A Irms at 110 nH and 0.32 mOhm typical DCR. It is a surface-mount part 3.0 mm or 4.0 mm tall, operating from -40 °C to +125 °C, and it is built for the phase node of a buck regulator where the inductor sets ripple and the control loop sets the rest.

    Key Specifications

    Orderable part numberFP0404R1-R110-R
    Inductance, OCL (0 Adc)110 nH
    Inductance, FLL (minimum)74.5 nH
    Irms (40 °C rise, no core loss)40 A
    Isat (20% roll-off @ +25 °C)14.2 A
    Isat2 (20% roll-off @ +100 °C)13 A
    Isat3 (20% roll-off @ +125 °C)11.8 A
    DCR typical @ +20 °C0.32 mOhm
    K-factor (Bp-p = K x L x dI)2,248
    Package4.0 x 4.0 mm, 3.0 mm / 4.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    Moisture sensitivity levelMSL 1
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    110 nH open-circuit, 74.5 nH at full load: that is a 32% roll-off purely from DC bias, before temperature enters the picture. Use the biased figure when you check peak current against saturation, and the unbiased one when you size the ripple.

    Peak current at 20% roll-off is 14.2 A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.

    Copper loss at the rated current works out at about 512 mW (40 A squared times 0.32 mOhm). That is the term the Irms rating measures. The missing term is core loss, and at a few hundred kilohertz it can be the larger of the two.

    Core loss needs flux, and flux here is about 105.3 mT for a 4.26 A ripple (K = 2,248). Double the ripple and the flux roughly doubles, but the loss does not - it climbs faster than linearly, which is why pushing ripple up to save inductance is not free.

    Series Positioning

    This is one of the smaller bodies in the FP range. At 4.0 x 4.0 mm it is meant for point-of-load stages and multi-phase VRMs where board area is the binding constraint and current per phase is tens of amps rather than hundreds. At 110 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it part 5 of 6 when the data sheet is sorted by inductance.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs), Server and desktop VRMs and EVRDs.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Sizing It Into a Design

    Size the inductor on peak current first, not average. With 110 nH the ripple can be a large fraction of the DC term at low inductance, so the peak may be well above the load current - and saturation cares about the peak.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.32 mOhm the winding is not the loss, the trace can be.

    Dimensions and Pad Layout

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP0404R1-R110-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    How is the part packed?
    Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.

    Is this part AEC-Q200 qualified?
    No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message