Eaton FP0505R1-R100-R - 100 nH Shielded Power Inductor 5.0 x 5.0 mm
Eaton FP0505R1-R100-R - 100 nH Shielded Power Inductor 5.0 x 5.0 mm

Eaton FP0505R1-R100-R - 100 nH Shielded Power Inductor 5.0 x 5.0 mm

Share
Eaton FP0505R1-R100-R: 100 nH high frequency, high current power inductor, 30 A Irms, 34 A Isat, DCR 0.38 mOhm, 5.0 x 5.0 mm package.
    • Product Details
    • Download

    FP0505R1-R100-R at a glance: 100 nH high frequency, high current power inductor, 30 A Irms, 34 A Isat, DCR 0.38 mOhm, 5.0 x 5.0 mm body, 4.8 mm tall.

    Eaton FP0505R1-R100-R High frequency, high current power inductors

    Eaton builds the FP0505R1-R100-R as a high frequency, high current power inductor for 5.0 x 5.0 mm footprints. At 100 nH and 30 A Irms with 0.38 mOhm of DCR it targets high-current DC-DC stages; the 4.8 mm tall body keeps the height budget in check, and the part is rated from -40 °C to +125 °C.

    Electrical Specifications

    Orderable part numberFP0505R1-R100-R
    Inductance, OCL (0 Adc)100 nH
    Inductance, FLL (minimum)68 nH
    Irms (40 °C rise, no core loss)30 A
    Isat (20% roll-off @ +25 °C)34 A
    Isat2 (20% roll-off @ +100 °C)26 A
    Isat3 (20% roll-off @ +125 °C)24 A
    DCR typical @ +20 °C0.38 mOhm
    K-factor (Bp-p = K x L x dI)1,279
    Package5.0 x 5.0 mm, 4.8 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    Two inductance figures are published. 100 nH is measured with no DC in the winding, 68 nH with the winding loaded to Isat1. The gap between them is 32%, and it is the reason a converter that looks well damped at no load can ring at full current.

    Peak current at 20% roll-off is 34 A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.

    Irms of 30 A is a thermal rating: the current that lifts the part about 40 °C with no core loss counted. Into 0.38 mOhm that is roughly 342 mW of copper loss, which is where the rise comes from. Add core loss and the usable DC current falls below the tabulated value.

    Core loss needs flux, and flux here is about 130.5 mT for a 10.2 A ripple (K = 1,279). Double the ripple and the flux roughly doubles, but the loss does not - it climbs faster than linearly, which is why pushing ripple up to save inductance is not free.

    Positioning in the FP Range

    This is one of the smaller bodies in the FP range. At 5.0 x 5.0 mm it is meant for point-of-load stages and multi-phase VRMs where board area is the binding constraint and current per phase is tens of amps rather than hundreds. At 100 nH this is a low-inductance point for the family, which means high ripple for a given input voltage and duty cycle. That is the intent: these parts are chosen when the converter switches fast and the inductor shapes the ripple rather than storing bulk energy.

    • Application fit: Servers, Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs).
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Putting It to Work

    The order of checks that works: compute ripple from 100 nH and the duty cycle, add half of it to the DC load to get peak, compare that peak with Isat at the real ambient, and only then look at Irms for heating. Doing it the other way round hides saturation problems.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.38 mOhm the winding is not the loss, the trace can be.

    Mechanical Drawing

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP0505R1-R100-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Can I substitute a lower inductance in the same body?
    Only after checking saturation. Lower inductance means higher ripple and a higher peak current for the same DC load. The part with less inductance usually has more saturation headroom, but the ripple penalty is real, so recalculate peak current before substituting.

    Is this part AEC-Q200 qualified?
    No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message