Eaton FP0607V1-R050-R 56 A SMD Power Inductor, 50 nH
Eaton FP0607V1-R050-R 56 A SMD Power Inductor, 50 nH

Eaton FP0607V1-R050-R 56 A SMD Power Inductor, 50 nH

Share
pEaton FP0607V1-R050-R: 50 nH high frequency, high current power inductor, 56 A Irms, 90 A Isat, DCR 0.24 mOhm, 6.0 x 5.3 mm package./p
    • Product Details
    • Download

    FP0607V1-R050-R at a glance: 50 nH high frequency, high current power inductor, 56 A Irms, 90 A Isat, DCR 0.24 mOhm, 6.0 x 5.3 mm body, 6.6 mm tall.

    Eaton FP0607V1-R050-R High frequency, high current power inductors

    The FP0607V1-R050-R is a 6.0 x 5.3 mm high frequency, high current power inductor from Eaton, rated 56 A Irms at 50 nH and 0.24 mOhm typical DCR. It is a surface-mount part 6.6 mm tall, operating from -40 °C to +125 °C, and it is built for the phase node of a buck regulator where the inductor sets ripple and the control loop sets the rest.

    Key Specifications

    Orderable part numberFP0607V1-R050-R
    Inductance, OCL (0 Adc)50 nH
    Inductance, FLL (minimum)32 nH
    Irms (40 °C rise, no core loss)56 A
    Isat (20% roll-off @ +25 °C)90 A
    Isat2 (20% roll-off @ +85 °C)76 A
    Isat3 (20% roll-off @ +100 °C)73 A
    DCR typical @ +20 °C0.24 mOhm
    K-factor (Bp-p = K x L x dI)735.3
    Package6.0 x 5.3 mm, 6.6 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    Moisture sensitivity levelMSL 1
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    At zero bias the winding measures 50 nH. Put Isat1 through it and the figure falls to 32 nH, about 36% lower, because the ferrite is partly saturated. Ripple calculations belong on the 50 nH number; loop stability and worst-case current belong on the lower one.

    Peak current at 20% roll-off is 90 A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.

    The 753 mW dissipated at 56 A through 0.24 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.

    Flux swing follows Bp-p = K x L x dI. With K = 735.3 and a ripple of 27 A the core sees roughly 99.3 mT, which is the number to put into the core-loss curve before you trust a 40 °C rise estimate.

    Series Positioning

    This is one of the smaller bodies in the FP range. At 6.0 x 5.3 mm it is meant for point-of-load stages and multi-phase VRMs where board area is the binding constraint and current per phase is tens of amps rather than hundreds. At 50 nH this is a low-inductance point for the family, which means high ripple for a given input voltage and duty cycle. That is the intent: these parts are chosen when the converter switches fast and the inductor shapes the ripple rather than storing bulk energy.

    • Application fit: Multi-phase and Vcore regulators, Voltage regulator modules (VRMs) and high power density VRMs, Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Design Notes

    Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 50 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.24 mOhm the winding is not the loss, the trace can be.

    Dimensions and Pad Layout

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP0607V1-R050-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Is this part AEC-Q200 qualified?
    No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.

    Can I substitute a lower inductance in the same body?
    Only after checking saturation. Lower inductance means higher ripple and a higher peak current for the same DC load. The part with less inductance usually has more saturation headroom, but the ripple penalty is real, so recalculate peak current before substituting.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products