Eaton FP0705R2-R10-R - 105 nH Shielded Power Inductor 7.0 x 7.0 mm
Eaton FP0705R2-R10-R - 105 nH Shielded Power Inductor 7.0 x 7.0 mm

Eaton FP0705R2-R10-R - 105 nH Shielded Power Inductor 7.0 x 7.0 mm

Share
pEaton FP0705R2-R10-R: 105 nH high frequency, high current power inductor, 38 A Irms, 44 A Isat, DCR 0.32 mOhm, 7.0 x 7.0 mm package./p
    • Product Details
    • Download

    FP0705R2-R10-R at a glance: 105 nH high frequency, high current power inductor, 38 A Irms, 44 A Isat, DCR 0.32 mOhm, 7.0 x 7.0 mm body, 4.95 mm tall.

    Eaton FP0705R2-R10-R High frequency, high current power inductors

    Eaton FP0705R2-R10-R is a high frequency, high current power inductor in a 7.0 x 7.0 mm surface-mount package. It carries 105 nH of open-circuit inductance with 38 A Irms and a typical DCR of 0.32 mOhm, which places it in the switching stage of a multi-phase regulator rather than in bulk energy storage. The body is 4.95 mm tall and rated from -40 °C to +125 °C.

    Ratings at a Glance

    Orderable part numberFP0705R2-R10-R
    Inductance, OCL (0 Adc)105 nH
    Inductance, FLL (minimum)78 nH
    Irms (40 °C rise, no core loss)38 A
    Isat (20% roll-off @ +25 °C)44 A
    Isat2 (20% roll-off @ +125 °C)34 A
    DCR typical @ +20 °C0.32 mOhm
    K-factor (Bp-p = K x L x dI)826
    Package7.0 x 7.0 mm, 4.95 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    At zero bias the winding measures 105 nH. Put Isat1 through it and the figure falls to 78 nH, about 26% lower, because the ferrite is partly saturated. Ripple calculations belong on the 105 nH number; loop stability and worst-case current belong on the lower one.

    Saturation is quoted as 20% roll-off at 44 A at +25 °C. That is a convention rather than a cliff: past it the inductance keeps falling, and how quickly depends on how hard the core is driven. Compare your worst-case peak against this number, not the average current.

    Copper loss at the rated current works out at about 462 mW (38 A squared times 0.32 mOhm). That is the term the Irms rating measures. The missing term is core loss, and at a few hundred kilohertz it can be the larger of the two.

    Flux swing follows Bp-p = K x L x dI. With K = 826 and a ripple of 13.2 A the core sees roughly 114.5 mT, which is the number to put into the core-loss curve before you trust a 40 °C rise estimate.

    Positioning in the FP Range

    The 7.0 x 7.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 105 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it part 4 of 18 when the data sheet is sorted by inductance, DCR sits between the 0.25 and 0.46 mOhm the series covers.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs), Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Putting It to Work

    Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 105 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.32 mOhm the winding is not the loss, the trace can be.

    Mechanical Dimensions and Pad Layout

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP0705R2-R10-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Is this part AEC-Q200 qualified?
    No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.

    Can I substitute a lower inductance in the same body?
    Only after checking saturation. Lower inductance means higher ripple and a higher peak current for the same DC load. The part with less inductance usually has more saturation headroom, but the ripple penalty is real, so recalculate peak current before substituting.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products