Eaton FP0705R3-R10-R High Current Inductor, 105 nH 0.46 mOhm
Eaton FP0705R3-R10-R High Current Inductor, 105 nH 0.46 mOhm

Eaton FP0705R3-R10-R High Current Inductor, 105 nH 0.46 mOhm

Share
pEaton FP0705R3-R10-R: 105 nH high frequency, high current power inductor, 32 A Irms, 44 A Isat, DCR 0.46 mOhm, 7.0 x 7.0 mm package./p
    • Product Details
    • Download

    FP0705R3-R10-R at a glance: 105 nH high frequency, high current power inductor, 32 A Irms, 44 A Isat, DCR 0.46 mOhm, 7.0 x 7.0 mm body, 4.95 mm tall.

    Eaton FP0705R3-R10-R High frequency, high current power inductors

    Eaton builds the FP0705R3-R10-R as a high frequency, high current power inductor for 7.0 x 7.0 mm footprints. At 105 nH and 32 A Irms with 0.46 mOhm of DCR it targets high-current DC-DC stages; the 4.95 mm tall body keeps the height budget in check, and the part is rated from -40 °C to +125 °C.

    Key Specifications

    Orderable part numberFP0705R3-R10-R
    Inductance, OCL (0 Adc)105 nH
    Inductance, FLL (minimum)78 nH
    Irms (40 °C rise, no core loss)32 A
    Isat (20% roll-off @ +25 °C)44 A
    Isat2 (20% roll-off @ +125 °C)34 A
    DCR typical @ +20 °C0.46 mOhm
    K-factor (Bp-p = K x L x dI)826
    Package7.0 x 7.0 mm, 4.95 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    105 nH open-circuit, 78 nH at full load: that is a 26% roll-off purely from DC bias, before temperature enters the picture. Use the biased figure when you check peak current against saturation, and the unbiased one when you size the ripple.

    Saturation is quoted as 20% roll-off at 44 A at +25 °C. That is a convention rather than a cliff: past it the inductance keeps falling, and how quickly depends on how hard the core is driven. Compare your worst-case peak against this number, not the average current.

    The 471 mW dissipated at 32 A through 0.46 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.

    Core loss needs flux, and flux here is about 114.5 mT for a 13.2 A ripple (K = 826). Double the ripple and the flux roughly doubles, but the loss does not - it climbs faster than linearly, which is why pushing ripple up to save inductance is not free.

    Series Positioning

    The 7.0 x 7.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 105 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it part 4 of 18 when the data sheet is sorted by inductance, with the highest DCR in the series at 0.46 mOhm, which is what the extra turns cost, Irms of 32 A is the bottom of the family.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs), Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Sizing It Into a Design

    Size the inductor on peak current first, not average. With 105 nH the ripple can be a large fraction of the DC term at low inductance, so the peak may be well above the load current - and saturation cares about the peak.

    On the board, place the part so the switch-node copper is short and wide. At 0.46 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Dimensions and Pad Layout

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP0705R3-R10-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Why is the saturation current listed at several temperatures?
    Because the ferrite loses permeability as it heats, so the same winding saturates at a lower current when it is hot. The columns let you read the value at the temperature your board actually runs at instead of scaling a room-temperature number by guesswork.

    What does the R suffix on the part number mean?
    It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message