Eaton FP0705R3-R12-R 32 A SMD Power Inductor, 120 nH
Eaton FP0705R3-R12-R 32 A SMD Power Inductor, 120 nH

Eaton FP0705R3-R12-R 32 A SMD Power Inductor, 120 nH

Share
pEaton FP0705R3-R12-R: 120 nH high frequency, high current power inductor, 32 A Irms, 37 A Isat, DCR 0.46 mOhm, 7.0 x 7.0 mm package./p
    • Product Details
    • Download

    FP0705R3-R12-R at a glance: 120 nH high frequency, high current power inductor, 32 A Irms, 37 A Isat, DCR 0.46 mOhm, 7.0 x 7.0 mm body, 4.95 mm tall.

    Eaton FP0705R3-R12-R High frequency, high current power inductors

    FP0705R3-R12-R is one of Eaton's high frequency, high current power inductor series, 7.0 x 7.0 mm with a 4.95 mm tall profile. Electrically it offers 120 nH at 32 A Irms and 0.46 mOhm typical DCR, which is the combination you want when the rail carries tens of amps and the board has no room for a larger can.

    Key Specifications

    Orderable part numberFP0705R3-R12-R
    Inductance, OCL (0 Adc)120 nH
    Inductance, FLL (minimum)86 nH
    Irms (40 °C rise, no core loss)32 A
    Isat (20% roll-off @ +25 °C)37 A
    Isat2 (20% roll-off @ +125 °C)30 A
    DCR typical @ +20 °C0.46 mOhm
    K-factor (Bp-p = K x L x dI)826
    Package7.0 x 7.0 mm, 4.95 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    The Figures Explained

    120 nH open-circuit, 86 nH at full load: that is a 28% roll-off purely from DC bias, before temperature enters the picture. Use the biased figure when you check peak current against saturation, and the unbiased one when you size the ripple.

    Peak current at 20% roll-off is 37 A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.

    The 471 mW dissipated at 32 A through 0.46 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.

    Core loss needs flux, and flux here is about 110 mT for a 11.1 A ripple (K = 826). Double the ripple and the flux roughly doubles, but the loss does not - it climbs faster than linearly, which is why pushing ripple up to save inductance is not free.

    Positioning in the FP Range

    The 7.0 x 7.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 120 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it part 7 of 18 when the data sheet is sorted by inductance, with the highest DCR in the series at 0.46 mOhm, which is what the extra turns cost, Irms of 32 A is the bottom of the family.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs), Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Sizing and Layout Notes

    The order of checks that works: compute ripple from 120 nH and the duty cycle, add half of it to the DC load to get peak, compare that peak with Isat at the real ambient, and only then look at Irms for heating. Doing it the other way round hides saturation problems.

    On the board, place the part so the switch-node copper is short and wide. At 0.46 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Mechanical Drawing

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP0705R3-R12-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    What does the R suffix on the part number mean?
    It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.

    Why is the saturation current listed at several temperatures?
    Because the ferrite loses permeability as it heats, so the same winding saturates at a lower current when it is hot. The columns let you read the value at the temperature your board actually runs at instead of scaling a room-temperature number by guesswork.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message