Eaton FP0705R3-R18-R 180 nH Power Inductor, 32 A
Eaton FP0705R3-R18-R 180 nH Power Inductor, 32 A

Eaton FP0705R3-R18-R 180 nH Power Inductor, 32 A

Share
pEaton FP0705R3-R18-R: 180 nH high frequency, high current power inductor, 32 A Irms, 25 A Isat, DCR 0.46 mOhm, 7.0 x 7.0 mm package./p
    • Product Details
    • Download

    FP0705R3-R18-R at a glance: 180 nH high frequency, high current power inductor, 32 A Irms, 25 A Isat, DCR 0.46 mOhm, 7.0 x 7.0 mm body, 4.95 mm tall.

    Eaton FP0705R3-R18-R High frequency, high current power inductors

    FP0705R3-R18-R is one of Eaton's high frequency, high current power inductor series, 7.0 x 7.0 mm with a 4.95 mm tall profile. Electrically it offers 180 nH at 32 A Irms and 0.46 mOhm typical DCR, which is the combination you want when the rail carries tens of amps and the board has no room for a larger can.

    Specification Table

    Orderable part numberFP0705R3-R18-R
    Inductance, OCL (0 Adc)180 nH
    Inductance, FLL (minimum)130 nH
    Irms (40 °C rise, no core loss)32 A
    Isat (20% roll-off @ +25 °C)25 A
    Isat2 (20% roll-off @ +125 °C)20 A
    DCR typical @ +20 °C0.46 mOhm
    K-factor (Bp-p = K x L x dI)826
    Package7.0 x 7.0 mm, 4.95 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    The Figures Explained

    At zero bias the winding measures 180 nH. Put Isat1 through it and the figure falls to 130 nH, about 28% lower, because the ferrite is partly saturated. Ripple calculations belong on the 180 nH number; loop stability and worst-case current belong on the lower one.

    Peak current at 20% roll-off is 25 A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.

    Irms of 32 A is a thermal rating: the current that lifts the part about 40 °C with no core loss counted. Into 0.46 mOhm that is roughly 471 mW of copper loss, which is where the rise comes from. Add core loss and the usable DC current falls below the tabulated value.

    Flux swing follows Bp-p = K x L x dI. With K = 826 and a ripple of 7.5 A the core sees roughly 111.5 mT, which is the number to put into the core-loss curve before you trust a 40 °C rise estimate.

    Positioning in the FP Range

    The 7.0 x 7.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 180 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it part 13 of 18 when the data sheet is sorted by inductance, with the highest DCR in the series at 0.46 mOhm, which is what the extra turns cost, Irms of 32 A is the bottom of the family.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs), Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Design Notes

    Size the inductor on peak current first, not average. With 180 nH the ripple can be a large fraction of the DC term at low inductance, so the peak may be well above the load current - and saturation cares about the peak.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.46 mOhm the winding is not the loss, the trace can be.

    Outline Drawing

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP0705R3-R18-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Why is the saturation current listed at several temperatures?
    Because the ferrite loses permeability as it heats, so the same winding saturates at a lower current when it is hot. The columns let you read the value at the temperature your board actually runs at instead of scaling a room-temperature number by guesswork.

    What does the R suffix on the part number mean?
    It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message