Eaton FP0705R3-R22-R - 226 nH Shielded Power Inductor 7.0 x 7.0 mm
Eaton FP0705R3-R22-R - 226 nH Shielded Power Inductor 7.0 x 7.0 mm

Eaton FP0705R3-R22-R - 226 nH Shielded Power Inductor 7.0 x 7.0 mm

Share
pEaton FP0705R3-R22-R: 226 nH high frequency, high current power inductor, 32 A Irms, 20 A Isat, DCR 0.46 mOhm, 7.0 x 7.0 mm package./p
    • Product Details
    • Download

    FP0705R3-R22-R at a glance: 226 nH high frequency, high current power inductor, 32 A Irms, 20 A Isat, DCR 0.46 mOhm, 7.0 x 7.0 mm body, 4.95 mm tall.

    Eaton FP0705R3-R22-R High frequency, high current power inductors

    FP0705R3-R22-R is one of Eaton's high frequency, high current power inductor series, 7.0 x 7.0 mm with a 4.95 mm tall profile. Electrically it offers 226 nH at 32 A Irms and 0.46 mOhm typical DCR, which is the combination you want when the rail carries tens of amps and the board has no room for a larger can.

    Specification Table

    Orderable part numberFP0705R3-R22-R
    Inductance, OCL (0 Adc)226 nH
    Inductance, FLL (minimum)159 nH
    Irms (40 °C rise, no core loss)32 A
    Isat (20% roll-off @ +25 °C)20 A
    Isat2 (20% roll-off @ +125 °C)16 A
    DCR typical @ +20 °C0.46 mOhm
    K-factor (Bp-p = K x L x dI)826
    Package7.0 x 7.0 mm, 4.95 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    226 nH open-circuit, 159 nH at full load: that is a 30% roll-off purely from DC bias, before temperature enters the picture. Use the biased figure when you check peak current against saturation, and the unbiased one when you size the ripple.

    The first Isat column, 20 A at +25 °C, is the peak the part takes at 20% roll-off. Note the temperature: run the same part in a hot enclosure and the usable peak drops, which is why the data sheet prints more than one column.

    Copper loss at the rated current works out at about 471 mW (32 A squared times 0.46 mOhm). That is the term the Irms rating measures. The missing term is core loss, and at a few hundred kilohertz it can be the larger of the two.

    Core loss needs flux, and flux here is about 112 mT for a 6 A ripple (K = 826). Double the ripple and the flux roughly doubles, but the loss does not - it climbs faster than linearly, which is why pushing ripple up to save inductance is not free.

    Where This Part Sits in the Range

    The 7.0 x 7.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 226 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it part 16 of 18 when the data sheet is sorted by inductance, with the highest DCR in the series at 0.46 mOhm, which is what the extra turns cost, Irms of 32 A is the bottom of the family.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs), Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Sizing It Into a Design

    Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 226 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.46 mOhm the winding is not the loss, the trace can be.

    Mechanical Dimensions and Pad Layout

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP0705R3-R22-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Why does DCR have both a typical and a maximum figure?
    The typical value is what the winding measures in production, the maximum is the limit the part is guaranteed to stay under. Size conduction loss on the maximum, because that is the worst case across a production run and over temperature.

    What does the R suffix on the part number mean?
    It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message