
FP0708R1-R10-R at a glance: 105 nH high frequency, high current power inductor, 44 A Irms, 68 A Isat, DCR 0.35 mOhm, 7.0 x 8.5 mm body, 7.2 mm tall.
Eaton FP0708R1-R10-R is a high frequency, high current power inductor in a 7.0 x 8.5 mm surface-mount package. It carries 105 nH of open-circuit inductance with 44 A Irms and a typical DCR of 0.35 mOhm, which places it in the switching stage of a multi-phase regulator rather than in bulk energy storage. The body is 7.2 mm tall and rated from -40 °C to +125 °C.
| Orderable part number | FP0708R1-R10-R |
| Inductance, OCL (0 Adc) | 105 nH |
| Inductance, FLL (minimum) | 75 nH |
| Irms (40 °C rise, no core loss) | 44 A |
| Isat (20% roll-off @ +25 °C) | 68 A |
| Isat2 (20% roll-off @ +125 °C) | 54 A |
| DCR typical @ +20 °C | 0.35 mOhm |
| K-factor (Bp-p = K x L x dI) | 557 |
| Package | 7.0 x 8.5 mm, 7.2 mm height |
| Core material | Ferrite, magnetically shielded |
| Operating temperature | -40 °C to +125 °C (ambient plus self-temperature rise) |
| RoHS | Compliant (-R suffix) |
At zero bias the winding measures 105 nH. Put Isat1 through it and the figure falls to 75 nH, about 29% lower, because the ferrite is partly saturated. Ripple calculations belong on the 105 nH number; loop stability and worst-case current belong on the lower one.
Saturation is quoted as 20% roll-off at 68 A at +25 °C. That is a convention rather than a cliff: past it the inductance keeps falling, and how quickly depends on how hard the core is driven. Compare your worst-case peak against this number, not the average current.
Irms of 44 A is a thermal rating: the current that lifts the part about 40 °C with no core loss counted. Into 0.35 mOhm that is roughly 678 mW of copper loss, which is where the rise comes from. Add core loss and the usable DC current falls below the tabulated value.
The K-factor of 557 turns ripple into flux: a peak-to-peak swing of 20.4 A gives about 119.3 mT peak in the core. Read the material loss curve at that flux and your switching frequency to get the loss term Irms leaves out.
The 7.0 x 8.5 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 105 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.
That makes it part 3 of 7 when the data sheet is sorted by inductance.
The order of checks that works: compute ripple from 105 nH and the duty cycle, add half of it to the DC load to get peak, compare that peak with Isat at the real ambient, and only then look at Irms for heating. Doing it the other way round hides saturation problems.
Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.35 mOhm the winding is not the loss, the trace can be.
Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

How is the part packed?
Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.
Is this part AEC-Q200 qualified?
No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.
Shenzhen Gaorunxin Technology Co., Ltd
Shenzhen Gaorunxin Technology Co., Ltd