Eaton FP0708R1-R19-R 44 A SMD Power Inductor, 190 nH
Eaton FP0708R1-R19-R 44 A SMD Power Inductor, 190 nH

Eaton FP0708R1-R19-R 44 A SMD Power Inductor, 190 nH

Share
pEaton FP0708R1-R19-R: 190 nH high frequency, high current power inductor, 44 A Irms, 37 A Isat, DCR 0.35 mOhm, 7.0 x 8.5 mm package./p
    • Product Details
    • Download

    FP0708R1-R19-R at a glance: 190 nH high frequency, high current power inductor, 44 A Irms, 37 A Isat, DCR 0.35 mOhm, 7.0 x 8.5 mm body, 7.2 mm tall.

    Eaton FP0708R1-R19-R High frequency, high current power inductors

    Eaton builds the FP0708R1-R19-R as a high frequency, high current power inductor for 7.0 x 8.5 mm footprints. At 190 nH and 44 A Irms with 0.35 mOhm of DCR it targets high-current DC-DC stages; the 7.2 mm tall body keeps the height budget in check, and the part is rated from -40 °C to +125 °C.

    Electrical Specifications

    Orderable part numberFP0708R1-R19-R
    Inductance, OCL (0 Adc)190 nH
    Inductance, FLL (minimum)135 nH
    Irms (40 °C rise, no core loss)44 A
    Isat (20% roll-off @ +25 °C)37 A
    Isat2 (20% roll-off @ +125 °C)29 A
    DCR typical @ +20 °C0.35 mOhm
    K-factor (Bp-p = K x L x dI)557
    Package7.0 x 8.5 mm, 7.2 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    The Figures Explained

    Two inductance figures are published. 190 nH is measured with no DC in the winding, 135 nH with the winding loaded to Isat1. The gap between them is 29%, and it is the reason a converter that looks well damped at no load can ring at full current.

    Peak current at 20% roll-off is 37 A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.

    Copper loss at the rated current works out at about 678 mW (44 A squared times 0.35 mOhm). That is the term the Irms rating measures. The missing term is core loss, and at a few hundred kilohertz it can be the larger of the two.

    Flux swing follows Bp-p = K x L x dI. With K = 557 and a ripple of 11.1 A the core sees roughly 117.5 mT, which is the number to put into the core-loss curve before you trust a 40 °C rise estimate.

    Series Positioning

    The 7.0 x 8.5 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 190 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it part 6 of 7 when the data sheet is sorted by inductance.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs), Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Sizing It Into a Design

    Size the inductor on peak current first, not average. With 190 nH the ripple can be a large fraction of the DC term at low inductance, so the peak may be well above the load current - and saturation cares about the peak.

    On the board, place the part so the switch-node copper is short and wide. At 0.35 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Mechanical Dimensions and Pad Layout

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP0708R1-R19-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    How is the part packed?
    Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.

    Is this part AEC-Q200 qualified?
    No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message