Eaton FP0805R1-R07-R High Current Inductor, 72 nH 0.17 mOhm
Eaton FP0805R1-R07-R High Current Inductor, 72 nH 0.17 mOhm

Eaton FP0805R1-R07-R High Current Inductor, 72 nH 0.17 mOhm

Share
pEaton FP0805R1-R07-R: 72 nH high frequency, high current power inductor, 65 A Irms, 67 A Isat, DCR 0.17 mOhm, 7.5 x 7.6 mm package./p
    • Product Details
    • Download

    FP0805R1-R07-R at a glance: 72 nH high frequency, high current power inductor, 65 A Irms, 67 A Isat, DCR 0.17 mOhm, 7.5 x 7.6 mm body, 5.0 mm tall.

    Eaton FP0805R1-R07-R High frequency, high current power inductors

    Eaton FP0805R1-R07-R is a high frequency, high current power inductor in a 7.5 x 7.6 mm surface-mount package. It carries 72 nH of open-circuit inductance with 65 A Irms and a typical DCR of 0.17 mOhm, which places it in the switching stage of a multi-phase regulator rather than in bulk energy storage. The body is 5.0 mm tall and rated from -40 °C to +125 °C.

    Ratings at a Glance

    Orderable part numberFP0805R1-R07-R
    Inductance, OCL (0 Adc)72 nH
    Inductance, FLL (minimum)52 nH
    Irms (40 °C rise, no core loss)65 A
    Isat (20% roll-off @ +25 °C)67 A
    Isat2 (20% roll-off @ +125 °C)49 A
    DCR typical @ +20 °C0.17 mOhm
    K-factor (Bp-p = K x L x dI)823.6
    Package7.5 x 7.6 mm, 5.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    The Figures Explained

    72 nH open-circuit, 52 nH at full load: that is a 28% roll-off purely from DC bias, before temperature enters the picture. Use the biased figure when you check peak current against saturation, and the unbiased one when you size the ripple.

    Saturation is quoted as 20% roll-off at 67 A at +25 °C. That is a convention rather than a cliff: past it the inductance keeps falling, and how quickly depends on how hard the core is driven. Compare your worst-case peak against this number, not the average current.

    Irms of 65 A is a thermal rating: the current that lifts the part about 40 °C with no core loss counted. Into 0.17 mOhm that is roughly 718 mW of copper loss, which is where the rise comes from. Add core loss and the usable DC current falls below the tabulated value.

    Flux swing follows Bp-p = K x L x dI. With K = 823.6 and a ripple of 20.1 A the core sees roughly 119.2 mT, which is the number to put into the core-loss curve before you trust a 40 °C rise estimate.

    Where This Part Sits in the Range

    The 7.5 x 7.6 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 72 nH this is a low-inductance point for the family, which means high ripple for a given input voltage and duty cycle. That is the intent: these parts are chosen when the converter switches fast and the inductor shapes the ripple rather than storing bulk energy.

    That makes it part 3 of 5 when the data sheet is sorted by inductance.

    • Application fit: Multi-phase and Vcore regulators.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Design Notes

    Size the inductor on peak current first, not average. With 72 nH the ripple can be a large fraction of the DC term at low inductance, so the peak may be well above the load current - and saturation cares about the peak.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.17 mOhm the winding is not the loss, the trace can be.

    Mechanical Drawing

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP0805R1-R07-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Why is the saturation current listed at several temperatures?
    Because the ferrite loses permeability as it heats, so the same winding saturates at a lower current when it is hot. The columns let you read the value at the temperature your board actually runs at instead of scaling a room-temperature number by guesswork.

    What does the R suffix on the part number mean?
    It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products