Eaton FP0807R1-R16-R 45 A SMD Power Inductor, 160 nH
Eaton FP0807R1-R16-R 45 A SMD Power Inductor, 160 nH

Eaton FP0807R1-R16-R 45 A SMD Power Inductor, 160 nH

Share
pEaton FP0807R1-R16-R: 160 nH high frequency, high current power inductor, 45 A Irms, 48 A Isat, DCR 36 mOhm, 8.0 x 7.0 mm package./p
    • Product Details
    • Download

    FP0807R1-R16-R at a glance: 160 nH high frequency, high current power inductor, 45 A Irms, 48 A Isat, DCR 36 mOhm, 8.0 x 7.0 mm body, 7.0 mm tall.

    Eaton FP0807R1-R16-R High frequency, high current power inductors

    The FP0807R1-R16-R is a 8.0 x 7.0 mm high frequency, high current power inductor from Eaton, rated 45 A Irms at 160 nH and 36 mOhm typical DCR. It is a surface-mount part 7.0 mm tall, operating from -40 °C to +125 °C, and it is built for the phase node of a buck regulator where the inductor sets ripple and the control loop sets the rest.

    Electrical Specifications

    Orderable part numberFP0807R1-R16-R
    Inductance, OCL (0 Adc)160 nH
    Inductance, FLL (minimum)115 nH
    Irms (40 °C rise, no core loss)45 A
    Isat (20% roll-off @ +25 °C)48 A
    DCR typical @ +20 °C36 mOhm
    K-factor (Bp-p = K x L x dI)520
    Package8.0 x 7.0 mm, 7.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    At zero bias the winding measures 160 nH. Put Isat1 through it and the figure falls to 115 nH, about 28% lower, because the ferrite is partly saturated. Ripple calculations belong on the 160 nH number; loop stability and worst-case current belong on the lower one.

    Peak current at 20% roll-off is 48 A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.

    Copper loss at the rated current works out at about 72900 mW (45 A squared times 36 mOhm). That is the term the Irms rating measures. The missing term is core loss, and at a few hundred kilohertz it can be the larger of the two.

    Core loss needs flux, and flux here is about 119.8 mT for a 14.4 A ripple (K = 520). Double the ripple and the flux roughly doubles, but the loss does not - it climbs faster than linearly, which is why pushing ripple up to save inductance is not free.

    Series Positioning

    The 8.0 x 7.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 160 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it part 4 of 7 when the data sheet is sorted by inductance, DCR sits between the 25 and 79 mOhm the series covers.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Module (VRM), Desktop and server VRMs and EVRDs.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Sizing and Layout Notes

    The order of checks that works: compute ripple from 160 nH and the duty cycle, add half of it to the DC load to get peak, compare that peak with Isat at the real ambient, and only then look at Irms for heating. Doing it the other way round hides saturation problems.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 36 mOhm the winding is not the loss, the trace can be.

    Mechanical Drawing

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP0807R1-R16-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Is this part AEC-Q200 qualified?
    No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.

    Why does DCR have both a typical and a maximum figure?
    The typical value is what the winding measures in production, the maximum is the limit the part is guaranteed to stay under. Size conduction loss on the maximum, because that is the worst case across a production run and over temperature.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products