Eaton FP0910V2-R100-R 100 nH 80 A Saturation Inductor
Eaton FP0910V2-R100-R 100 nH 80 A Saturation Inductor

Eaton FP0910V2-R100-R 100 nH 80 A Saturation Inductor

Share
pEaton FP0910V2-R100-R: 100 nH high frequency, high current power inductor, 63 A Irms, 80 A Isat, DCR 0.125 mOhm, 9.0 x 10.0 mm package./p
    • Product Details
    • Download

    FP0910V2-R100-R at a glance: 100 nH high frequency, high current power inductor, 63 A Irms, 80 A Isat, DCR 0.125 mOhm, 9.0 x 10.0 mm body, 9.5 mm tall.

    Eaton FP0910V2-R100-R High frequency, high current power inductors

    The FP0910V2-R100-R is a 9.0 x 10.0 mm high frequency, high current power inductor from Eaton, rated 63 A Irms at 100 nH and 0.125 mOhm typical DCR. It is a surface-mount part 9.5 mm tall, operating from -40 °C to +125 °C, and it is built for the phase node of a buck regulator where the inductor sets ripple and the control loop sets the rest.

    Specification Table

    Orderable part numberFP0910V2-R100-R
    Inductance, OCL (0 Adc)100 nH
    Inductance, FLL (minimum)72 nH
    Irms (40 °C rise, no core loss)63 A
    Isat (20% roll-off @ +25 °C)80 A
    Isat2 (20% roll-off @ +100 °C)70 A
    Isat3 (20% roll-off @ +125 °C)64 A
    DCR typical @ +20 °C0.125 mOhm
    K-factor (Bp-p = K x L x dI)455
    Package9.0 x 10.0 mm, 9.5 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    Moisture sensitivity levelMSL 1
    RoHSCompliant (-R suffix)

    The Figures Explained

    100 nH open-circuit, 72 nH at full load: that is a 28% roll-off purely from DC bias, before temperature enters the picture. Use the biased figure when you check peak current against saturation, and the unbiased one when you size the ripple.

    Saturation is quoted as 20% roll-off at 80 A at +25 °C. That is a convention rather than a cliff: past it the inductance keeps falling, and how quickly depends on how hard the core is driven. Compare your worst-case peak against this number, not the average current.

    Copper loss at the rated current works out at about 496 mW (63 A squared times 0.125 mOhm). That is the term the Irms rating measures. The missing term is core loss, and at a few hundred kilohertz it can be the larger of the two.

    The K-factor of 455 turns ripple into flux: a peak-to-peak swing of 24 A gives about 109.2 mT peak in the core. Read the material loss curve at that flux and your switching frequency to get the loss term Irms leaves out.

    Series Positioning

    The 9.0 x 10.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 100 nH this is a low-inductance point for the family, which means high ripple for a given input voltage and duty cycle. That is the intent: these parts are chosen when the converter switches fast and the inductor shapes the ripple rather than storing bulk energy.

    That makes it the lowest inductance of the 7 parts in this data sheet, and it shares the lowest DCR here at 0.125 mOhm, Irms of 63 A is the top of the family.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs) and high- power density VRMs, Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Sizing and Layout Notes

    Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 100 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.

    On the board, place the part so the switch-node copper is short and wide. At 0.125 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Dimensions and Pad Layout

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP0910V2-R100-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Why does DCR have both a typical and a maximum figure?
    The typical value is what the winding measures in production, the maximum is the limit the part is guaranteed to stay under. Size conduction loss on the maximum, because that is the worst case across a production run and over temperature.

    Can I substitute a lower inductance in the same body?
    Only after checking saturation. Lower inductance means higher ripple and a higher peak current for the same DC load. The part with less inductance usually has more saturation headroom, but the ripple penalty is real, so recalculate peak current before substituting.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products