Eaton FP0910V3-R150-R 44 A SMD Power Inductor, 150 nH
Eaton FP0910V3-R150-R 44 A SMD Power Inductor, 150 nH

Eaton FP0910V3-R150-R 44 A SMD Power Inductor, 150 nH

Share
pEaton FP0910V3-R150-R: 150 nH high frequency, high current power inductor, 44 A Irms, 68 A Isat, DCR 0.4 mOhm, 9.0 x 10.0 mm package./p
    • Product Details
    • Download

    FP0910V3-R150-R at a glance: 150 nH high frequency, high current power inductor, 44 A Irms, 68 A Isat, DCR 0.4 mOhm, 9.0 x 10.0 mm body, 9.5 mm tall.

    Eaton FP0910V3-R150-R High frequency, high current power inductors

    Eaton builds the FP0910V3-R150-R as a high frequency, high current power inductor for 9.0 x 10.0 mm footprints. At 150 nH and 44 A Irms with 0.4 mOhm of DCR it targets high-current DC-DC stages; the 9.5 mm tall body keeps the height budget in check, and the part is rated from -40 °C to +125 °C.

    Electrical Specifications

    Orderable part numberFP0910V3-R150-R
    Inductance, OCL (0 Adc)150 nH
    Inductance, FLL (minimum)105 nH
    Irms (40 °C rise, no core loss)44 A
    Isat (20% roll-off @ +25 °C)68 A
    Isat2 (20% roll-off @ +100 °C)58 A
    Isat3 (20% roll-off @ +125 °C)54 A
    DCR typical @ +20 °C0.4 mOhm
    K-factor (Bp-p = K x L x dI)340
    Package9.0 x 10.0 mm, 9.5 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    Moisture sensitivity levelMSL 1
    RoHSCompliant (-R suffix)

    How to Read These Ratings

    At zero bias the winding measures 150 nH. Put Isat1 through it and the figure falls to 105 nH, about 30% lower, because the ferrite is partly saturated. Ripple calculations belong on the 150 nH number; loop stability and worst-case current belong on the lower one.

    Peak current at 20% roll-off is 68 A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.

    The 774 mW dissipated at 44 A through 0.4 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.

    Core loss needs flux, and flux here is about 104 mT for a 20.4 A ripple (K = 340). Double the ripple and the flux roughly doubles, but the loss does not - it climbs faster than linearly, which is why pushing ripple up to save inductance is not free.

    Where This Part Sits in the Range

    The 9.0 x 10.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 150 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it part 3 of 7 when the data sheet is sorted by inductance, with the highest DCR in the series at 0.4 mOhm, which is what the extra turns cost, Irms of 44 A is the bottom of the family.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs) and high- power density VRMs, Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Sizing and Layout Notes

    The order of checks that works: compute ripple from 150 nH and the duty cycle, add half of it to the DC load to get peak, compare that peak with Isat at the real ambient, and only then look at Irms for heating. Doing it the other way round hides saturation problems.

    On the board, place the part so the switch-node copper is short and wide. At 0.4 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Outline Drawing

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP0910V3-R150-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Why is the saturation current listed at several temperatures?
    Because the ferrite loses permeability as it heats, so the same winding saturates at a lower current when it is hot. The columns let you read the value at the temperature your board actually runs at instead of scaling a room-temperature number by guesswork.

    What does the R suffix on the part number mean?
    It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products