Eaton FP0910V3-R330-R 330 nH 23 A Saturation Inductor
Eaton FP0910V3-R330-R 330 nH 23 A Saturation Inductor

Eaton FP0910V3-R330-R 330 nH 23 A Saturation Inductor

Share
pEaton FP0910V3-R330-R: 330 nH high frequency, high current power inductor, 44 A Irms, 23 A Isat, DCR 0.4 mOhm, 9.0 x 10.0 mm package./p
    • Product Details
    • Download

    FP0910V3-R330-R at a glance: 330 nH high frequency, high current power inductor, 44 A Irms, 23 A Isat, DCR 0.4 mOhm, 9.0 x 10.0 mm body, 9.5 mm tall.

    Eaton FP0910V3-R330-R High frequency, high current power inductors

    The FP0910V3-R330-R is a 9.0 x 10.0 mm high frequency, high current power inductor from Eaton, rated 44 A Irms at 330 nH and 0.4 mOhm typical DCR. It is a surface-mount part 9.5 mm tall, operating from -40 °C to +125 °C, and it is built for the phase node of a buck regulator where the inductor sets ripple and the control loop sets the rest.

    Ratings at a Glance

    Orderable part numberFP0910V3-R330-R
    Inductance, OCL (0 Adc)330 nH
    Inductance, FLL (minimum)231 nH
    Irms (40 °C rise, no core loss)44 A
    Isat (20% roll-off @ +25 °C)23 A
    Isat2 (20% roll-off @ +100 °C)19 A
    Isat3 (20% roll-off @ +125 °C)17 A
    DCR typical @ +20 °C0.4 mOhm
    K-factor (Bp-p = K x L x dI)340
    Package9.0 x 10.0 mm, 9.5 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    Moisture sensitivity levelMSL 1
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    At zero bias the winding measures 330 nH. Put Isat1 through it and the figure falls to 231 nH, about 30% lower, because the ferrite is partly saturated. Ripple calculations belong on the 330 nH number; loop stability and worst-case current belong on the lower one.

    Saturation is quoted as 20% roll-off at 23 A at +25 °C. That is a convention rather than a cliff: past it the inductance keeps falling, and how quickly depends on how hard the core is driven. Compare your worst-case peak against this number, not the average current.

    Copper loss at the rated current works out at about 774 mW (44 A squared times 0.4 mOhm). That is the term the Irms rating measures. The missing term is core loss, and at a few hundred kilohertz it can be the larger of the two.

    Flux swing follows Bp-p = K x L x dI. With K = 340 and a ripple of 6.9 A the core sees roughly 77.4 mT, which is the number to put into the core-loss curve before you trust a 40 °C rise estimate.

    Series Positioning

    The 9.0 x 10.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 330 nH this sits at the high-inductance end of the family. Ripple is small and core loss with it, but there is less headroom before saturation, because saturation current falls as inductance rises in the same can.

    That makes it part 5 of 7 when the data sheet is sorted by inductance, with the highest DCR in the series at 0.4 mOhm, which is what the extra turns cost, Irms of 44 A is the bottom of the family.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs) and high- power density VRMs, Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Sizing It Into a Design

    Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 330 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.4 mOhm the winding is not the loss, the trace can be.

    Mechanical Drawing

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP0910V3-R330-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Is this part AEC-Q200 qualified?
    No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.

    How is the part packed?
    Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message