
FP1005R1-R08-R at a glance: 85 nH high frequency, high current power inductor, 53 A Irms, 90 A Isat, DCR 0.39 mOhm, 10.2 x 7.0 mm body, 4.95 mm tall.
FP1005R1-R08-R is one of Eaton's high frequency, high current power inductor series, 10.2 x 7.0 mm with a 4.95 mm tall profile. Electrically it offers 85 nH at 53 A Irms and 0.39 mOhm typical DCR, which is the combination you want when the rail carries tens of amps and the board has no room for a larger can.
| Orderable part number | FP1005R1-R08-R |
| Inductance, OCL (0 Adc) | 85 nH |
| Inductance, FLL (minimum) | 61 nH |
| Irms (40 °C rise, no core loss) | 53 A |
| Isat (20% roll-off @ +25 °C) | 90 A |
| Isat2 (20% roll-off @ +125 °C) | 64 A |
| DCR typical @ +20 °C | 0.39 mOhm |
| K-factor (Bp-p = K x L x dI) | 536 |
| Package | 10.2 x 7.0 mm, 4.95 mm height |
| Core material | Ferrite, magnetically shielded |
| Operating temperature | -40 °C to +125 °C (ambient plus self-temperature rise) |
| RoHS | Compliant (-R suffix) |
Two inductance figures are published. 85 nH is measured with no DC in the winding, 61 nH with the winding loaded to Isat1. The gap between them is 28%, and it is the reason a converter that looks well damped at no load can ring at full current.
The first Isat column, 90 A at +25 °C, is the peak the part takes at 20% roll-off. Note the temperature: run the same part in a hot enclosure and the usable peak drops, which is why the data sheet prints more than one column.
Copper loss at the rated current works out at about 1096 mW (53 A squared times 0.39 mOhm). That is the term the Irms rating measures. The missing term is core loss, and at a few hundred kilohertz it can be the larger of the two.
Core loss needs flux, and flux here is about 123 mT for a 27 A ripple (K = 536). Double the ripple and the flux roughly doubles, but the loss does not - it climbs faster than linearly, which is why pushing ripple up to save inductance is not free.
The 10.2 x 7.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 85 nH this is a low-inductance point for the family, which means high ripple for a given input voltage and duty cycle. That is the intent: these parts are chosen when the converter switches fast and the inductor shapes the ripple rather than storing bulk energy.
That makes it the lowest inductance of the 16 parts in this data sheet, and it shares the lowest DCR here at 0.39 mOhm, Irms of 53 A is the top of the family.
Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 85 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.
On the board, place the part so the switch-node copper is short and wide. At 0.39 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.
The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

Why is the saturation current listed at several temperatures?
Because the ferrite loses permeability as it heats, so the same winding saturates at a lower current when it is hot. The columns let you read the value at the temperature your board actually runs at instead of scaling a room-temperature number by guesswork.
Can I substitute a lower inductance in the same body?
Only after checking saturation. Lower inductance means higher ripple and a higher peak current for the same DC load. The part with less inductance usually has more saturation headroom, but the ripple penalty is real, so recalculate peak current before substituting.
Shenzhen Gaorunxin Technology Co., Ltd
Shenzhen Gaorunxin Technology Co., Ltd