Eaton FP1005R1-R10-R High Current Inductor, 100 nH 0.39 mOhm
Eaton FP1005R1-R10-R High Current Inductor, 100 nH 0.39 mOhm

Eaton FP1005R1-R10-R High Current Inductor, 100 nH 0.39 mOhm

Share
pEaton FP1005R1-R10-R: 100 nH high frequency, high current power inductor, 53 A Irms, 73 A Isat, DCR 0.39 mOhm, 10.2 x 7.0 mm package./p
    • Product Details
    • Download

    FP1005R1-R10-R at a glance: 100 nH high frequency, high current power inductor, 53 A Irms, 73 A Isat, DCR 0.39 mOhm, 10.2 x 7.0 mm body, 4.95 mm tall.

    Eaton FP1005R1-R10-R High frequency, high current power inductors

    Eaton builds the FP1005R1-R10-R as a high frequency, high current power inductor for 10.2 x 7.0 mm footprints. At 100 nH and 53 A Irms with 0.39 mOhm of DCR it targets high-current DC-DC stages; the 4.95 mm tall body keeps the height budget in check, and the part is rated from -40 °C to +125 °C.

    Electrical Specifications

    Orderable part numberFP1005R1-R10-R
    Inductance, OCL (0 Adc)100 nH
    Inductance, FLL (minimum)72 nH
    Irms (40 °C rise, no core loss)53 A
    Isat (20% roll-off @ +25 °C)73 A
    Isat2 (20% roll-off @ +125 °C)57 A
    DCR typical @ +20 °C0.39 mOhm
    K-factor (Bp-p = K x L x dI)536
    Package10.2 x 7.0 mm, 4.95 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    At zero bias the winding measures 100 nH. Put Isat1 through it and the figure falls to 72 nH, about 28% lower, because the ferrite is partly saturated. Ripple calculations belong on the 100 nH number; loop stability and worst-case current belong on the lower one.

    Saturation is quoted as 20% roll-off at 73 A at +25 °C. That is a convention rather than a cliff: past it the inductance keeps falling, and how quickly depends on how hard the core is driven. Compare your worst-case peak against this number, not the average current.

    Irms of 53 A is a thermal rating: the current that lifts the part about 40 °C with no core loss counted. Into 0.39 mOhm that is roughly 1096 mW of copper loss, which is where the rise comes from. Add core loss and the usable DC current falls below the tabulated value.

    The K-factor of 536 turns ripple into flux: a peak-to-peak swing of 21.9 A gives about 117.4 mT peak in the core. Read the material loss curve at that flux and your switching frequency to get the loss term Irms leaves out.

    What This Family Is For

    The 10.2 x 7.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 100 nH this is a low-inductance point for the family, which means high ripple for a given input voltage and duty cycle. That is the intent: these parts are chosen when the converter switches fast and the inductor shapes the ripple rather than storing bulk energy.

    That makes it part 4 of 16 when the data sheet is sorted by inductance, and it shares the lowest DCR here at 0.39 mOhm, Irms of 53 A is the top of the family.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs), Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Design Notes

    Size the inductor on peak current first, not average. With 100 nH the ripple can be a large fraction of the DC term at low inductance, so the peak may be well above the load current - and saturation cares about the peak.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.39 mOhm the winding is not the loss, the trace can be.

    Dimensions and Pad Layout

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP1005R1-R10-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    How is the part packed?
    Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.

    Is this part AEC-Q200 qualified?
    No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products