Eaton FP1005R1-R12-R 53 A SMD Power Inductor, 120 nH
Eaton FP1005R1-R12-R 53 A SMD Power Inductor, 120 nH

Eaton FP1005R1-R12-R 53 A SMD Power Inductor, 120 nH

Share
pEaton FP1005R1-R12-R: 120 nH high frequency, high current power inductor, 53 A Irms, 60 A Isat, DCR 0.39 mOhm, 10.2 x 7.0 mm package./p
    • Product Details
    • Download

    FP1005R1-R12-R at a glance: 120 nH high frequency, high current power inductor, 53 A Irms, 60 A Isat, DCR 0.39 mOhm, 10.2 x 7.0 mm body, 4.95 mm tall.

    Eaton FP1005R1-R12-R High frequency, high current power inductors

    Eaton FP1005R1-R12-R is a high frequency, high current power inductor in a 10.2 x 7.0 mm surface-mount package. It carries 120 nH of open-circuit inductance with 53 A Irms and a typical DCR of 0.39 mOhm, which places it in the switching stage of a multi-phase regulator rather than in bulk energy storage. The body is 4.95 mm tall and rated from -40 °C to +125 °C.

    Electrical Specifications

    Orderable part numberFP1005R1-R12-R
    Inductance, OCL (0 Adc)120 nH
    Inductance, FLL (minimum)86 nH
    Irms (40 °C rise, no core loss)53 A
    Isat (20% roll-off @ +25 °C)60 A
    Isat2 (20% roll-off @ +125 °C)48 A
    DCR typical @ +20 °C0.39 mOhm
    K-factor (Bp-p = K x L x dI)536
    Package10.2 x 7.0 mm, 4.95 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    How to Read These Ratings

    At zero bias the winding measures 120 nH. Put Isat1 through it and the figure falls to 86 nH, about 28% lower, because the ferrite is partly saturated. Ripple calculations belong on the 120 nH number; loop stability and worst-case current belong on the lower one.

    Saturation is quoted as 20% roll-off at 60 A at +25 °C. That is a convention rather than a cliff: past it the inductance keeps falling, and how quickly depends on how hard the core is driven. Compare your worst-case peak against this number, not the average current.

    Irms of 53 A is a thermal rating: the current that lifts the part about 40 °C with no core loss counted. Into 0.39 mOhm that is roughly 1096 mW of copper loss, which is where the rise comes from. Add core loss and the usable DC current falls below the tabulated value.

    Core loss needs flux, and flux here is about 115.8 mT for a 18 A ripple (K = 536). Double the ripple and the flux roughly doubles, but the loss does not - it climbs faster than linearly, which is why pushing ripple up to save inductance is not free.

    Positioning in the FP Range

    The 10.2 x 7.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 120 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it part 7 of 16 when the data sheet is sorted by inductance, and it shares the lowest DCR here at 0.39 mOhm, Irms of 53 A is the top of the family.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs), Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Design Notes

    The order of checks that works: compute ripple from 120 nH and the duty cycle, add half of it to the DC load to get peak, compare that peak with Isat at the real ambient, and only then look at Irms for heating. Doing it the other way round hides saturation problems.

    On the board, place the part so the switch-node copper is short and wide. At 0.39 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Mechanical Drawing

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP1005R1-R12-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Is this part AEC-Q200 qualified?
    No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.

    How is the part packed?
    Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products