Eaton FP1005R1-R22-R 220 nH Power Inductor, 53 A
Eaton FP1005R1-R22-R 220 nH Power Inductor, 53 A

Eaton FP1005R1-R22-R 220 nH Power Inductor, 53 A

Share
pEaton FP1005R1-R22-R: 220 nH high frequency, high current power inductor, 53 A Irms, 33 A Isat, DCR 0.39 mOhm, 10.2 x 7.0 mm package./p
    • Product Details
    • Download

    FP1005R1-R22-R at a glance: 220 nH high frequency, high current power inductor, 53 A Irms, 33 A Isat, DCR 0.39 mOhm, 10.2 x 7.0 mm body, 4.95 mm tall.

    Eaton FP1005R1-R22-R High frequency, high current power inductors

    FP1005R1-R22-R is one of Eaton's high frequency, high current power inductor series, 10.2 x 7.0 mm with a 4.95 mm tall profile. Electrically it offers 220 nH at 53 A Irms and 0.39 mOhm typical DCR, which is the combination you want when the rail carries tens of amps and the board has no room for a larger can.

    Electrical Specifications

    Orderable part numberFP1005R1-R22-R
    Inductance, OCL (0 Adc)220 nH
    Inductance, FLL (minimum)158 nH
    Irms (40 °C rise, no core loss)53 A
    Isat (20% roll-off @ +25 °C)33 A
    Isat2 (20% roll-off @ +125 °C)26 A
    DCR typical @ +20 °C0.39 mOhm
    K-factor (Bp-p = K x L x dI)536
    Package10.2 x 7.0 mm, 4.95 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    How to Read These Ratings

    Two inductance figures are published. 220 nH is measured with no DC in the winding, 158 nH with the winding loaded to Isat1. The gap between them is 28%, and it is the reason a converter that looks well damped at no load can ring at full current.

    Peak current at 20% roll-off is 33 A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.

    The 1096 mW dissipated at 53 A through 0.39 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.

    The K-factor of 536 turns ripple into flux: a peak-to-peak swing of 9.9 A gives about 116.7 mT peak in the core. Read the material loss curve at that flux and your switching frequency to get the loss term Irms leaves out.

    What This Family Is For

    The 10.2 x 7.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 220 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it part 14 of 16 when the data sheet is sorted by inductance, and it shares the lowest DCR here at 0.39 mOhm, Irms of 53 A is the top of the family.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs), Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Sizing It Into a Design

    The order of checks that works: compute ripple from 220 nH and the duty cycle, add half of it to the DC load to get peak, compare that peak with Isat at the real ambient, and only then look at Irms for heating. Doing it the other way round hides saturation problems.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.39 mOhm the winding is not the loss, the trace can be.

    Mechanical Drawing

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP1005R1-R22-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Why does DCR have both a typical and a maximum figure?
    The typical value is what the winding measures in production, the maximum is the limit the part is guaranteed to stay under. Size conduction loss on the maximum, because that is the worst case across a production run and over temperature.

    What does the R suffix on the part number mean?
    It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products