Eaton FP1005R2-R12-R 50 A SMD Power Inductor, 120 nH
Eaton FP1005R2-R12-R 50 A SMD Power Inductor, 120 nH

Eaton FP1005R2-R12-R 50 A SMD Power Inductor, 120 nH

Share
pEaton FP1005R2-R12-R: 120 nH high frequency, high current power inductor, 50 A Irms, 60 A Isat, DCR 0.47 mOhm, 10.2 x 7.0 mm package./p
    • Product Details
    • Download

    FP1005R2-R12-R at a glance: 120 nH high frequency, high current power inductor, 50 A Irms, 60 A Isat, DCR 0.47 mOhm, 10.2 x 7.0 mm body, 4.95 mm tall.

    Eaton FP1005R2-R12-R High frequency, high current power inductors

    Eaton FP1005R2-R12-R is a high frequency, high current power inductor in a 10.2 x 7.0 mm surface-mount package. It carries 120 nH of open-circuit inductance with 50 A Irms and a typical DCR of 0.47 mOhm, which places it in the switching stage of a multi-phase regulator rather than in bulk energy storage. The body is 4.95 mm tall and rated from -40 °C to +125 °C.

    Electrical Specifications

    Orderable part numberFP1005R2-R12-R
    Inductance, OCL (0 Adc)120 nH
    Inductance, FLL (minimum)86 nH
    Irms (40 °C rise, no core loss)50 A
    Isat (20% roll-off @ +25 °C)60 A
    Isat2 (20% roll-off @ +125 °C)48 A
    DCR typical @ +20 °C0.47 mOhm
    K-factor (Bp-p = K x L x dI)536
    Package10.2 x 7.0 mm, 4.95 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    At zero bias the winding measures 120 nH. Put Isat1 through it and the figure falls to 86 nH, about 28% lower, because the ferrite is partly saturated. Ripple calculations belong on the 120 nH number; loop stability and worst-case current belong on the lower one.

    The first Isat column, 60 A at +25 °C, is the peak the part takes at 20% roll-off. Note the temperature: run the same part in a hot enclosure and the usable peak drops, which is why the data sheet prints more than one column.

    The 1175 mW dissipated at 50 A through 0.47 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.

    The K-factor of 536 turns ripple into flux: a peak-to-peak swing of 18 A gives about 115.8 mT peak in the core. Read the material loss curve at that flux and your switching frequency to get the loss term Irms leaves out.

    Where This Part Sits in the Range

    The 10.2 x 7.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 120 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it part 7 of 16 when the data sheet is sorted by inductance, DCR sits between the 0.39 and 0.7 mOhm the series covers.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs), Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Design Notes

    Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 120 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.

    On the board, place the part so the switch-node copper is short and wide. At 0.47 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Mechanical Drawing

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP1005R2-R12-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Why is the saturation current listed at several temperatures?
    Because the ferrite loses permeability as it heats, so the same winding saturates at a lower current when it is hot. The columns let you read the value at the temperature your board actually runs at instead of scaling a room-temperature number by guesswork.

    Can I substitute a lower inductance in the same body?
    Only after checking saturation. Lower inductance means higher ripple and a higher peak current for the same DC load. The part with less inductance usually has more saturation headroom, but the ripple penalty is real, so recalculate peak current before substituting.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products