
FP1005R3-R22-R at a glance: 220 nH high frequency, high current power inductor, 45 A Irms, 33 A Isat, DCR 0.55 mOhm, 10.2 x 7.0 mm body, 4.95 mm tall.
FP1005R3-R22-R is one of Eaton's high frequency, high current power inductor series, 10.2 x 7.0 mm with a 4.95 mm tall profile. Electrically it offers 220 nH at 45 A Irms and 0.55 mOhm typical DCR, which is the combination you want when the rail carries tens of amps and the board has no room for a larger can.
| Orderable part number | FP1005R3-R22-R |
| Inductance, OCL (0 Adc) | 220 nH |
| Inductance, FLL (minimum) | 158 nH |
| Irms (40 °C rise, no core loss) | 45 A |
| Isat (20% roll-off @ +25 °C) | 33 A |
| Isat2 (20% roll-off @ +125 °C) | 26 A |
| DCR typical @ +20 °C | 0.55 mOhm |
| K-factor (Bp-p = K x L x dI) | 536 |
| Package | 10.2 x 7.0 mm, 4.95 mm height |
| Core material | Ferrite, magnetically shielded |
| Operating temperature | -40 °C to +125 °C (ambient plus self-temperature rise) |
| RoHS | Compliant (-R suffix) |
220 nH open-circuit, 158 nH at full load: that is a 28% roll-off purely from DC bias, before temperature enters the picture. Use the biased figure when you check peak current against saturation, and the unbiased one when you size the ripple.
Peak current at 20% roll-off is 33 A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.
The 1114 mW dissipated at 45 A through 0.55 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.
Flux swing follows Bp-p = K x L x dI. With K = 536 and a ripple of 9.9 A the core sees roughly 116.7 mT, which is the number to put into the core-loss curve before you trust a 40 °C rise estimate.
The 10.2 x 7.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 220 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.
That makes it part 14 of 16 when the data sheet is sorted by inductance, DCR sits between the 0.39 and 0.7 mOhm the series covers, Irms of 45 A is the bottom of the family.
The order of checks that works: compute ripple from 220 nH and the duty cycle, add half of it to the DC load to get peak, compare that peak with Isat at the real ambient, and only then look at Irms for heating. Doing it the other way round hides saturation problems.
Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.55 mOhm the winding is not the loss, the trace can be.
The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

Is this part AEC-Q200 qualified?
No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.
Can I substitute a lower inductance in the same body?
Only after checking saturation. Lower inductance means higher ripple and a higher peak current for the same DC load. The part with less inductance usually has more saturation headroom, but the ripple penalty is real, so recalculate peak current before substituting.
Shenzhen Gaorunxin Technology Co., Ltd
Shenzhen Gaorunxin Technology Co., Ltd