Eaton FP1005R4-R12-R - 120 nH Shielded Power Inductor 10.2 x 7.0 mm
Eaton FP1005R4-R12-R - 120 nH Shielded Power Inductor 10.2 x 7.0 mm

Eaton FP1005R4-R12-R - 120 nH Shielded Power Inductor 10.2 x 7.0 mm

Share
pEaton FP1005R4-R12-R: 120 nH high frequency, high current power inductor, 45 A Irms, 60 A Isat, DCR 0.7 mOhm, 10.2 x 7.0 mm package./p
    • Product Details
    • Download

    FP1005R4-R12-R at a glance: 120 nH high frequency, high current power inductor, 45 A Irms, 60 A Isat, DCR 0.7 mOhm, 10.2 x 7.0 mm body, 4.95 mm tall.

    Eaton FP1005R4-R12-R High frequency, high current power inductors

    FP1005R4-R12-R is one of Eaton's high frequency, high current power inductor series, 10.2 x 7.0 mm with a 4.95 mm tall profile. Electrically it offers 120 nH at 45 A Irms and 0.7 mOhm typical DCR, which is the combination you want when the rail carries tens of amps and the board has no room for a larger can.

    Specification Table

    Orderable part numberFP1005R4-R12-R
    Inductance, OCL (0 Adc)120 nH
    Inductance, FLL (minimum)86 nH
    Irms (40 °C rise, no core loss)45 A
    Isat (20% roll-off @ +25 °C)60 A
    Isat2 (20% roll-off @ +125 °C)48 A
    DCR typical @ +20 °C0.7 mOhm
    K-factor (Bp-p = K x L x dI)536
    Package10.2 x 7.0 mm, 4.95 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    120 nH open-circuit, 86 nH at full load: that is a 28% roll-off purely from DC bias, before temperature enters the picture. Use the biased figure when you check peak current against saturation, and the unbiased one when you size the ripple.

    Peak current at 20% roll-off is 60 A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.

    Irms of 45 A is a thermal rating: the current that lifts the part about 40 °C with no core loss counted. Into 0.7 mOhm that is roughly 1418 mW of copper loss, which is where the rise comes from. Add core loss and the usable DC current falls below the tabulated value.

    The K-factor of 536 turns ripple into flux: a peak-to-peak swing of 18 A gives about 115.8 mT peak in the core. Read the material loss curve at that flux and your switching frequency to get the loss term Irms leaves out.

    Series Positioning

    The 10.2 x 7.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 120 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it part 7 of 16 when the data sheet is sorted by inductance, with the highest DCR in the series at 0.7 mOhm, which is what the extra turns cost, Irms of 45 A is the bottom of the family.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs), Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Putting It to Work

    Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 120 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.7 mOhm the winding is not the loss, the trace can be.

    Dimensions and Pad Layout

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP1005R4-R12-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    How is the part packed?
    Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.

    Is this part AEC-Q200 qualified?
    No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products