Eaton FP1006R1-R16-R 160 nH Power Inductor, - A
Eaton FP1006R1-R16-R 160 nH Power Inductor, - A

Eaton FP1006R1-R16-R 160 nH Power Inductor, - A

Share
pEaton FP1006R1-R16-R: 160 nH high frequency, high current power inductor, A Irms, A Isat, DCR 0.27 mOhm, 10.2 x 8.0 mm package./p
    • Product Details
    • Download

    FP1006R1-R16-R at a glance: 160 nH high frequency, high current power inductor, - A Irms, - A Isat, DCR 0.27 mOhm, 10.2 x 8.0 mm body, 6.0 mm tall.

    Eaton FP1006R1-R16-R High frequency, high current power inductors

    FP1006R1-R16-R is one of Eaton's high frequency, high current power inductor series, 10.2 x 8.0 mm with a 6.0 mm tall profile. Electrically it offers 160 nH at - A Irms and 0.27 mOhm typical DCR, which is the combination you want when the rail carries tens of amps and the board has no room for a larger can.

    Ratings at a Glance

    Orderable part numberFP1006R1-R16-R
    Inductance, OCL (0 Adc)160 nH
    Inductance, FLL (minimum)115 nH
    Isat2 (20% roll-off @ +125 °C)55 A
    DCR typical @ +20 °C0.27 mOhm
    K-factor (Bp-p = K x L x dI)454
    Package10.2 x 8.0 mm, 6.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    160 nH open-circuit, 115 nH at full load: that is a 28% roll-off purely from DC bias, before temperature enters the picture. Use the biased figure when you check peak current against saturation, and the unbiased one when you size the ripple.

    The first Isat column, - A at +25 °C, is the peak the part takes at 20% roll-off. Note the temperature: run the same part in a hot enclosure and the usable peak drops, which is why the data sheet prints more than one column.

    Copper loss at the rated current works out at about 0 mW (- A squared times 0.27 mOhm). That is the term the Irms rating measures. The missing term is core loss, and at a few hundred kilohertz it can be the larger of the two.

    The data sheet for this part does not publish a K-factor, so core loss has to come from the loss curve rather than from a formula. If the ripple is large, measure it on the bench rather than assuming the 40 °C Irms margin covers it.

    Positioning in the FP Range

    The 10.2 x 8.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 160 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it part 7 of 10 when the data sheet is sorted by inductance, and it shares the lowest DCR here at 0.27 mOhm.

    • Application fit: Multi-phase and Vcore regulators.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Design Notes

    The order of checks that works: compute ripple from 160 nH and the duty cycle, add half of it to the DC load to get peak, compare that peak with Isat at the real ambient, and only then look at Irms for heating. Doing it the other way round hides saturation problems.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.27 mOhm the winding is not the loss, the trace can be.

    Dimensions and Pad Layout

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP1006R1-R16-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    What does the R suffix on the part number mean?
    It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.

    Why is the saturation current listed at several temperatures?
    Because the ferrite loses permeability as it heats, so the same winding saturates at a lower current when it is hot. The columns let you read the value at the temperature your board actually runs at instead of scaling a room-temperature number by guesswork.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products