Eaton FP1006R2-R10-R - A SMD Power Inductor, 100 nH
Eaton FP1006R2-R10-R - A SMD Power Inductor, 100 nH

Eaton FP1006R2-R10-R - A SMD Power Inductor, 100 nH

Share
pEaton FP1006R2-R10-R: 100 nH high frequency, high current power inductor, A Irms, A Isat, DCR 0.36 mOhm, 10.2 x 8.0 mm package./p
    • Product Details
    • Download

    FP1006R2-R10-R at a glance: 100 nH high frequency, high current power inductor, - A Irms, - A Isat, DCR 0.36 mOhm, 10.2 x 8.0 mm body, 6.0 mm tall.

    Eaton FP1006R2-R10-R High frequency, high current power inductors

    Eaton builds the FP1006R2-R10-R as a high frequency, high current power inductor for 10.2 x 8.0 mm footprints. At 100 nH and - A Irms with 0.36 mOhm of DCR it targets high-current DC-DC stages; the 6.0 mm tall body keeps the height budget in check, and the part is rated from -40 °C to +125 °C.

    Specification Table

    Orderable part numberFP1006R2-R10-R
    Inductance, OCL (0 Adc)100 nH
    Inductance, FLL (minimum)72 nH
    Isat2 (20% roll-off @ +125 °C)85 A
    DCR typical @ +20 °C0.36 mOhm
    K-factor (Bp-p = K x L x dI)454
    Package10.2 x 8.0 mm, 6.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    100 nH open-circuit, 72 nH at full load: that is a 28% roll-off purely from DC bias, before temperature enters the picture. Use the biased figure when you check peak current against saturation, and the unbiased one when you size the ripple.

    Peak current at 20% roll-off is - A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.

    The 0 mW dissipated at - A through 0.36 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.

    The data sheet for this part does not publish a K-factor, so core loss has to come from the loss curve rather than from a formula. If the ripple is large, measure it on the bench rather than assuming the 40 °C Irms margin covers it.

    Positioning in the FP Range

    The 10.2 x 8.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 100 nH this is a low-inductance point for the family, which means high ripple for a given input voltage and duty cycle. That is the intent: these parts are chosen when the converter switches fast and the inductor shapes the ripple rather than storing bulk energy.

    That makes it part 3 of 10 when the data sheet is sorted by inductance, with the highest DCR in the series at 0.36 mOhm, which is what the extra turns cost.

    • Application fit: Multi-phase and Vcore regulators.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Sizing It Into a Design

    Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 100 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.

    On the board, place the part so the switch-node copper is short and wide. At 0.36 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Mechanical Dimensions and Pad Layout

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP1006R2-R10-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Why is the saturation current listed at several temperatures?
    Because the ferrite loses permeability as it heats, so the same winding saturates at a lower current when it is hot. The columns let you read the value at the temperature your board actually runs at instead of scaling a room-temperature number by guesswork.

    Can I substitute a lower inductance in the same body?
    Only after checking saturation. Lower inductance means higher ripple and a higher peak current for the same DC load. The part with less inductance usually has more saturation headroom, but the ripple penalty is real, so recalculate peak current before substituting.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products