Eaton FP1007R1-R14-R High Current Inductor, 140 nH 0.29 mOhm
Eaton FP1007R1-R14-R High Current Inductor, 140 nH 0.29 mOhm

Eaton FP1007R1-R14-R High Current Inductor, 140 nH 0.29 mOhm

Share
pEaton FP1007R1-R14-R: 140 nH high frequency, high current power inductor, 60 A Irms, 72 A Isat, DCR 0.29 mOhm, 10.4 x 8.0 mm package./p
    • Product Details
    • Download

    FP1007R1-R14-R at a glance: 140 nH high frequency, high current power inductor, 60 A Irms, 72 A Isat, DCR 0.29 mOhm, 10.4 x 8.0 mm body, 7.5 mm tall.

    Eaton FP1007R1-R14-R High frequency, high current power inductors

    The FP1007R1-R14-R is a 10.4 x 8.0 mm high frequency, high current power inductor from Eaton, rated 60 A Irms at 140 nH and 0.29 mOhm typical DCR. It is a surface-mount part 7.5 mm tall, operating from -40 °C to +125 °C, and it is built for the phase node of a buck regulator where the inductor sets ripple and the control loop sets the rest.

    Specification Table

    Orderable part numberFP1007R1-R14-R
    Inductance, OCL (0 Adc)140 nH
    Inductance, FLL (minimum)100 nH
    Irms (40 °C rise, no core loss)60 A
    Isat (20% roll-off @ +25 °C)72 A
    Isat2 (20% roll-off @ +125 °C)56 A
    DCR typical @ +20 °C0.29 mOhm
    K-factor (Bp-p = K x L x dI)371
    Package10.4 x 8.0 mm, 7.5 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    The Figures Explained

    At zero bias the winding measures 140 nH. Put Isat1 through it and the figure falls to 100 nH, about 29% lower, because the ferrite is partly saturated. Ripple calculations belong on the 140 nH number; loop stability and worst-case current belong on the lower one.

    Saturation is quoted as 20% roll-off at 72 A at +25 °C. That is a convention rather than a cliff: past it the inductance keeps falling, and how quickly depends on how hard the core is driven. Compare your worst-case peak against this number, not the average current.

    Irms of 60 A is a thermal rating: the current that lifts the part about 40 °C with no core loss counted. Into 0.29 mOhm that is roughly 1044 mW of copper loss, which is where the rise comes from. Add core loss and the usable DC current falls below the tabulated value.

    Core loss needs flux, and flux here is about 112.2 mT for a 21.6 A ripple (K = 371). Double the ripple and the flux roughly doubles, but the loss does not - it climbs faster than linearly, which is why pushing ripple up to save inductance is not free.

    Series Positioning

    The 10.4 x 8.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 140 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it part 4 of 17 when the data sheet is sorted by inductance, and it shares the lowest DCR here at 0.29 mOhm.

    • Application fit: Servers, Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs).
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Sizing and Layout Notes

    The order of checks that works: compute ripple from 140 nH and the duty cycle, add half of it to the DC load to get peak, compare that peak with Isat at the real ambient, and only then look at Irms for heating. Doing it the other way round hides saturation problems.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.29 mOhm the winding is not the loss, the trace can be.

    Dimensions and Pad Layout

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP1007R1-R14-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    How is the part packed?
    Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.

    Is this part AEC-Q200 qualified?
    No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message