Eaton FP1007R1-R22-R 215 nH 50 A Saturation Inductor
Eaton FP1007R1-R22-R 215 nH 50 A Saturation Inductor

Eaton FP1007R1-R22-R 215 nH 50 A Saturation Inductor

Share
pEaton FP1007R1-R22-R: 215 nH high frequency, high current power inductor, 60 A Irms, 50 A Isat, DCR 0.29 mOhm, 10.4 x 8.0 mm package./p
    • Product Details
    • Download

    FP1007R1-R22-R at a glance: 215 nH high frequency, high current power inductor, 60 A Irms, 50 A Isat, DCR 0.29 mOhm, 10.4 x 8.0 mm body, 7.5 mm tall.

    Eaton FP1007R1-R22-R High frequency, high current power inductors

    Eaton builds the FP1007R1-R22-R as a high frequency, high current power inductor for 10.4 x 8.0 mm footprints. At 215 nH and 60 A Irms with 0.29 mOhm of DCR it targets high-current DC-DC stages; the 7.5 mm tall body keeps the height budget in check, and the part is rated from -40 °C to +125 °C.

    Specification Table

    Orderable part numberFP1007R1-R22-R
    Inductance, OCL (0 Adc)215 nH
    Inductance, FLL (minimum)155 nH
    Irms (40 °C rise, no core loss)60 A
    Isat (20% roll-off @ +25 °C)50 A
    Isat2 (20% roll-off @ +125 °C)36 A
    DCR typical @ +20 °C0.29 mOhm
    K-factor (Bp-p = K x L x dI)371
    Package10.4 x 8.0 mm, 7.5 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    How to Read These Ratings

    Two inductance figures are published. 215 nH is measured with no DC in the winding, 155 nH with the winding loaded to Isat1. The gap between them is 28%, and it is the reason a converter that looks well damped at no load can ring at full current.

    Saturation is quoted as 20% roll-off at 50 A at +25 °C. That is a convention rather than a cliff: past it the inductance keeps falling, and how quickly depends on how hard the core is driven. Compare your worst-case peak against this number, not the average current.

    The 1044 mW dissipated at 60 A through 0.29 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.

    Flux swing follows Bp-p = K x L x dI. With K = 371 and a ripple of 15 A the core sees roughly 119.6 mT, which is the number to put into the core-loss curve before you trust a 40 °C rise estimate.

    Series Positioning

    The 10.4 x 8.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 215 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it part 10 of 17 when the data sheet is sorted by inductance, and it shares the lowest DCR here at 0.29 mOhm.

    • Application fit: Servers, Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs).
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Sizing and Layout Notes

    The order of checks that works: compute ripple from 215 nH and the duty cycle, add half of it to the DC load to get peak, compare that peak with Isat at the real ambient, and only then look at Irms for heating. Doing it the other way round hides saturation problems.

    On the board, place the part so the switch-node copper is short and wide. At 0.29 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Mechanical Drawing

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP1007R1-R22-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    How is the part packed?
    Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.

    What does the R suffix on the part number mean?
    It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products