Eaton FP1007R2-R17-R 51 A SMD Power Inductor, 170 nH
Eaton FP1007R2-R17-R 51 A SMD Power Inductor, 170 nH

Eaton FP1007R2-R17-R 51 A SMD Power Inductor, 170 nH

Share
pEaton FP1007R2-R17-R: 170 nH high frequency, high current power inductor, 51 A Irms, 58 A Isat, DCR 0.48 mOhm, 10.4 x 8.0 mm package./p
    • Product Details
    • Download

    FP1007R2-R17-R at a glance: 170 nH high frequency, high current power inductor, 51 A Irms, 58 A Isat, DCR 0.48 mOhm, 10.4 x 8.0 mm body, 7.5 mm tall.

    Eaton FP1007R2-R17-R High frequency, high current power inductors

    Eaton FP1007R2-R17-R is a high frequency, high current power inductor in a 10.4 x 8.0 mm surface-mount package. It carries 170 nH of open-circuit inductance with 51 A Irms and a typical DCR of 0.48 mOhm, which places it in the switching stage of a multi-phase regulator rather than in bulk energy storage. The body is 7.5 mm tall and rated from -40 °C to +125 °C.

    Ratings at a Glance

    Orderable part numberFP1007R2-R17-R
    Inductance, OCL (0 Adc)170 nH
    Inductance, FLL (minimum)122 nH
    Irms (40 °C rise, no core loss)51 A
    Isat (20% roll-off @ +25 °C)58 A
    Isat2 (20% roll-off @ +125 °C)46 A
    DCR typical @ +20 °C0.48 mOhm
    K-factor (Bp-p = K x L x dI)368
    Package10.4 x 8.0 mm, 7.5 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    At zero bias the winding measures 170 nH. Put Isat1 through it and the figure falls to 122 nH, about 28% lower, because the ferrite is partly saturated. Ripple calculations belong on the 170 nH number; loop stability and worst-case current belong on the lower one.

    The first Isat column, 58 A at +25 °C, is the peak the part takes at 20% roll-off. Note the temperature: run the same part in a hot enclosure and the usable peak drops, which is why the data sheet prints more than one column.

    Copper loss at the rated current works out at about 1248 mW (51 A squared times 0.48 mOhm). That is the term the Irms rating measures. The missing term is core loss, and at a few hundred kilohertz it can be the larger of the two.

    The K-factor of 368 turns ripple into flux: a peak-to-peak swing of 17.4 A gives about 108.9 mT peak in the core. Read the material loss curve at that flux and your switching frequency to get the loss term Irms leaves out.

    What This Family Is For

    The 10.4 x 8.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 170 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it part 7 of 17 when the data sheet is sorted by inductance, with the highest DCR in the series at 0.48 mOhm, which is what the extra turns cost, Irms of 51 A is the bottom of the family.

    • Application fit: Servers, Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs).
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Sizing It Into a Design

    Size the inductor on peak current first, not average. With 170 nH the ripple can be a large fraction of the DC term at low inductance, so the peak may be well above the load current - and saturation cares about the peak.

    On the board, place the part so the switch-node copper is short and wide. At 0.48 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Outline Drawing

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP1007R2-R17-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Why does DCR have both a typical and a maximum figure?
    The typical value is what the winding measures in production, the maximum is the limit the part is guaranteed to stay under. Size conduction loss on the maximum, because that is the worst case across a production run and over temperature.

    What does the R suffix on the part number mean?
    It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products