Eaton FP1008L1-R100-R High Current Inductor, 100 nH 0.17 mOhm
Eaton FP1008L1-R100-R High Current Inductor, 100 nH 0.17 mOhm

Eaton FP1008L1-R100-R High Current Inductor, 100 nH 0.17 mOhm

Share
pEaton FP1008L1-R100-R: 100 nH high frequency, high current power inductor, 65 A Irms, 75 A Isat, DCR 0.17 mOhm, 10.0 x 8.0 mm package./p
    • Product Details
    • Download

    FP1008L1-R100-R at a glance: 100 nH high frequency, high current power inductor, 65 A Irms, 75 A Isat, DCR 0.17 mOhm, 10.0 x 8.0 mm body, 8.0 mm tall.

    Eaton FP1008L1-R100-R High frequency, high current power inductors

    Eaton builds the FP1008L1-R100-R as a high frequency, high current power inductor for 10.0 x 8.0 mm footprints. At 100 nH and 65 A Irms with 0.17 mOhm of DCR it targets high-current DC-DC stages; the 8.0 mm tall body keeps the height budget in check, and the part is rated from -40 °C to +125 °C.

    Key Specifications

    Orderable part numberFP1008L1-R100-R
    Inductance, OCL (0 Adc)100 nH
    Inductance, FLL (minimum)72 nH
    Irms (40 °C rise, no core loss)65 A
    Isat (20% roll-off @ +25 °C)75 A
    Isat2 (20% roll-off @ +100 °C)65 A
    Isat3 (20% roll-off @ +125 °C)63 A
    DCR typical @ +20 °C0.17 mOhm
    K-factor (Bp-p = K x L x dI)461
    Package10.0 x 8.0 mm, 8.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    At zero bias the winding measures 100 nH. Put Isat1 through it and the figure falls to 72 nH, about 28% lower, because the ferrite is partly saturated. Ripple calculations belong on the 100 nH number; loop stability and worst-case current belong on the lower one.

    Peak current at 20% roll-off is 75 A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.

    The 718 mW dissipated at 65 A through 0.17 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.

    Core loss needs flux, and flux here is about 103.7 mT for a 22.5 A ripple (K = 461). Double the ripple and the flux roughly doubles, but the loss does not - it climbs faster than linearly, which is why pushing ripple up to save inductance is not free.

    Series Positioning

    The 10.0 x 8.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 100 nH this is a low-inductance point for the family, which means high ripple for a given input voltage and duty cycle. That is the intent: these parts are chosen when the converter switches fast and the inductor shapes the ripple rather than storing bulk energy.

    That makes it the lowest inductance of the 3 parts in this data sheet.

    • Application fit: Servers, Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs).
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Sizing It Into a Design

    The order of checks that works: compute ripple from 100 nH and the duty cycle, add half of it to the DC load to get peak, compare that peak with Isat at the real ambient, and only then look at Irms for heating. Doing it the other way round hides saturation problems.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.17 mOhm the winding is not the loss, the trace can be.

    Mechanical Drawing

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP1008L1-R100-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    What does the R suffix on the part number mean?
    It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.

    Why is the saturation current listed at several temperatures?
    Because the ferrite loses permeability as it heats, so the same winding saturates at a lower current when it is hot. The columns let you read the value at the temperature your board actually runs at instead of scaling a room-temperature number by guesswork.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products