Eaton FP1008R5-R300-R 300 nH Power Inductor, 79 A
Eaton FP1008R5-R300-R 300 nH Power Inductor, 79 A

Eaton FP1008R5-R300-R 300 nH Power Inductor, 79 A

Share
pEaton FP1008R5-R300-R: 300 nH high frequency, high current power inductor, 79 A Irms, 36 A Isat, DCR 0.17 mOhm, 10.8 x 8.0 mm package./p
    • Product Details
    • Download

    FP1008R5-R300-R at a glance: 300 nH high frequency, high current power inductor, 79 A Irms, 36 A Isat, DCR 0.17 mOhm, 10.8 x 8.0 mm body, 8.0 mm tall.

    Eaton FP1008R5-R300-R High frequency, high current power inductors

    Eaton FP1008R5-R300-R is a high frequency, high current power inductor in a 10.8 x 8.0 mm surface-mount package. It carries 300 nH of open-circuit inductance with 79 A Irms and a typical DCR of 0.17 mOhm, which places it in the switching stage of a multi-phase regulator rather than in bulk energy storage. The body is 8.0 mm tall and rated from -40 °C to +125 °C.

    Ratings at a Glance

    Orderable part numberFP1008R5-R300-R
    Inductance, OCL (0 Adc)300 nH
    Inductance, FLL (minimum)216 nH
    Irms (40 °C rise, no core loss)79 A
    Isat (20% roll-off @ +25 °C)36 A
    Isat2 (20% roll-off @ +100 °C)28 A
    Isat3 (20% roll-off @ +125 °C)26 A
    DCR typical @ +20 °C0.17 mOhm
    K-factor (Bp-p = K x L x dI)342
    Package10.8 x 8.0 mm, 8.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    The Figures Explained

    Two inductance figures are published. 300 nH is measured with no DC in the winding, 216 nH with the winding loaded to Isat1. The gap between them is 28%, and it is the reason a converter that looks well damped at no load can ring at full current.

    The first Isat column, 36 A at +25 °C, is the peak the part takes at 20% roll-off. Note the temperature: run the same part in a hot enclosure and the usable peak drops, which is why the data sheet prints more than one column.

    The 1061 mW dissipated at 79 A through 0.17 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.

    Core loss needs flux, and flux here is about 110.8 mT for a 10.8 A ripple (K = 342). Double the ripple and the flux roughly doubles, but the loss does not - it climbs faster than linearly, which is why pushing ripple up to save inductance is not free.

    Where This Part Sits in the Range

    The 10.8 x 8.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 300 nH this sits at the high-inductance end of the family. Ripple is small and core loss with it, but there is less headroom before saturation, because saturation current falls as inductance rises in the same can.

    That makes it part 12 of 13 when the data sheet is sorted by inductance, and it shares the lowest DCR here at 0.17 mOhm, Irms of 79 A is the top of the family.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs) and high power density VRMs, Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Putting It to Work

    Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 300 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.

    On the board, place the part so the switch-node copper is short and wide. At 0.17 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Dimensions and Pad Layout

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP1008R5-R300-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Why does DCR have both a typical and a maximum figure?
    The typical value is what the winding measures in production, the maximum is the limit the part is guaranteed to stay under. Size conduction loss on the maximum, because that is the worst case across a production run and over temperature.

    Why is the saturation current listed at several temperatures?
    Because the ferrite loses permeability as it heats, so the same winding saturates at a lower current when it is hot. The columns let you read the value at the temperature your board actually runs at instead of scaling a room-temperature number by guesswork.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message