Eaton FP1008R6-R180-R 180 nH 70 A Saturation Inductor
Eaton FP1008R6-R180-R 180 nH 70 A Saturation Inductor

Eaton FP1008R6-R180-R 180 nH 70 A Saturation Inductor

Share
pEaton FP1008R6-R180-R: 180 nH high frequency, high current power inductor, 74 A Irms, 70 A Isat, DCR 0.18 mOhm, 10.8 x 8.0 mm package./p
    • Product Details
    • Download

    FP1008R6-R180-R at a glance: 180 nH high frequency, high current power inductor, 74 A Irms, 70 A Isat, DCR 0.18 mOhm, 10.8 x 8.0 mm body, 8.0 mm tall.

    Eaton FP1008R6-R180-R High frequency, high current power inductors

    Eaton FP1008R6-R180-R is a high frequency, high current power inductor in a 10.8 x 8.0 mm surface-mount package. It carries 180 nH of open-circuit inductance with 74 A Irms and a typical DCR of 0.18 mOhm, which places it in the switching stage of a multi-phase regulator rather than in bulk energy storage. The body is 8.0 mm tall and rated from -40 °C to +125 °C.

    Ratings at a Glance

    Orderable part numberFP1008R6-R180-R
    Inductance, OCL (0 Adc)180 nH
    Inductance, FLL (minimum)130 nH
    Irms (40 °C rise, no core loss)74 A
    Isat (20% roll-off @ +25 °C)70 A
    Isat2 (20% roll-off @ +100 °C)56 A
    Isat3 (20% roll-off @ +125 °C)53 A
    DCR typical @ +20 °C0.18 mOhm
    K-factor (Bp-p = K x L x dI)342
    Package10.8 x 8.0 mm, 8.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    How to Read These Ratings

    At zero bias the winding measures 180 nH. Put Isat1 through it and the figure falls to 130 nH, about 28% lower, because the ferrite is partly saturated. Ripple calculations belong on the 180 nH number; loop stability and worst-case current belong on the lower one.

    Saturation is quoted as 20% roll-off at 70 A at +25 °C. That is a convention rather than a cliff: past it the inductance keeps falling, and how quickly depends on how hard the core is driven. Compare your worst-case peak against this number, not the average current.

    Copper loss at the rated current works out at about 986 mW (74 A squared times 0.18 mOhm). That is the term the Irms rating measures. The missing term is core loss, and at a few hundred kilohertz it can be the larger of the two.

    The K-factor of 342 turns ripple into flux: a peak-to-peak swing of 21 A gives about 129.3 mT peak in the core. Read the material loss curve at that flux and your switching frequency to get the loss term Irms leaves out.

    Where This Part Sits in the Range

    The 10.8 x 8.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 180 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it part 6 of 13 when the data sheet is sorted by inductance, with the highest DCR in the series at 0.18 mOhm, which is what the extra turns cost, Irms of 74 A is the bottom of the family.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs) and high power density VRMs, Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Putting It to Work

    The order of checks that works: compute ripple from 180 nH and the duty cycle, add half of it to the DC load to get peak, compare that peak with Isat at the real ambient, and only then look at Irms for heating. Doing it the other way round hides saturation problems.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.18 mOhm the winding is not the loss, the trace can be.

    Dimensions and Pad Layout

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP1008R6-R180-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    What does the R suffix on the part number mean?
    It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.

    How is the part packed?
    Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message