Eaton FP1010R1-R150-R 50 A SMD Power Inductor, 150 nH
Eaton FP1010R1-R150-R 50 A SMD Power Inductor, 150 nH

Eaton FP1010R1-R150-R 50 A SMD Power Inductor, 150 nH

Share
pEaton FP1010R1-R150-R: 150 nH high frequency, high current power inductor, 50 A Irms, 80 A Isat, DCR 0.185 mOhm, 9.6 x 6.4 mm package./p
    • Product Details
    • Download

    FP1010R1-R150-R at a glance: 150 nH high frequency, high current power inductor, 50 A Irms, 80 A Isat, DCR 0.185 mOhm, 9.6 x 6.4 mm body, 10.4 mm tall.

    Eaton FP1010R1-R150-R High frequency, high current power inductors

    Eaton builds the FP1010R1-R150-R as a high frequency, high current power inductor for 9.6 x 6.4 mm footprints. At 150 nH and 50 A Irms with 0.185 mOhm of DCR it targets high-current DC-DC stages; the 10.4 mm tall body keeps the height budget in check, and the part is rated from -40 °C to +125 °C.

    Electrical Specifications

    Orderable part numberFP1010R1-R150-R
    Inductance, OCL (0 Adc)150 nH
    Inductance, FLL (minimum)105 nH
    Irms (40 °C rise, no core loss)50 A
    Isat (20% roll-off @ +25 °C)80 A
    Isat3 (20% roll-off @ +100 °C)68 A
    Isat4 (20% roll-off @ +125 °C)64 A
    DCR typical @ +20 °C0.185 mOhm
    K-factor (Bp-p = K x L x dI)371
    Package9.6 x 6.4 mm, 10.4 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    Moisture sensitivity levelMSL 1
    RoHSCompliant (-R suffix)

    The Figures Explained

    At zero bias the winding measures 150 nH. Put Isat1 through it and the figure falls to 105 nH, about 30% lower, because the ferrite is partly saturated. Ripple calculations belong on the 150 nH number; loop stability and worst-case current belong on the lower one.

    Peak current at 20% roll-off is 80 A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.

    The 462 mW dissipated at 50 A through 0.185 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.

    Flux swing follows Bp-p = K x L x dI. With K = 371 and a ripple of 24 A the core sees roughly 133.6 mT, which is the number to put into the core-loss curve before you trust a 40 °C rise estimate.

    What This Family Is For

    The 9.6 x 6.4 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 150 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it part 5 of 12 when the data sheet is sorted by inductance, with the highest DCR in the series at 0.185 mOhm, which is what the extra turns cost, Irms of 50 A is the bottom of the family.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs), Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Sizing It Into a Design

    The order of checks that works: compute ripple from 150 nH and the duty cycle, add half of it to the DC load to get peak, compare that peak with Isat at the real ambient, and only then look at Irms for heating. Doing it the other way round hides saturation problems.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.185 mOhm the winding is not the loss, the trace can be.

    Mechanical Drawing

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP1010R1-R150-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    How is the part packed?
    Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.

    Is this part AEC-Q200 qualified?
    No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products