
FP1010R1-R330-R at a glance: 330 nH high frequency, high current power inductor, 50 A Irms, 30 A Isat, DCR 0.185 mOhm, 9.6 x 6.4 mm body, 10.4 mm tall.
Eaton FP1010R1-R330-R is a high frequency, high current power inductor in a 9.6 x 6.4 mm surface-mount package. It carries 330 nH of open-circuit inductance with 50 A Irms and a typical DCR of 0.185 mOhm, which places it in the switching stage of a multi-phase regulator rather than in bulk energy storage. The body is 10.4 mm tall and rated from -40 °C to +125 °C.
| Orderable part number | FP1010R1-R330-R |
| Inductance, OCL (0 Adc) | 330 nH |
| Inductance, FLL (minimum) | 230 nH |
| Irms (40 °C rise, no core loss) | 50 A |
| Isat (20% roll-off @ +25 °C) | 30 A |
| Isat3 (20% roll-off @ +100 °C) | 25 A |
| Isat4 (20% roll-off @ +125 °C) | 23 A |
| DCR typical @ +20 °C | 0.185 mOhm |
| K-factor (Bp-p = K x L x dI) | 371 |
| Package | 9.6 x 6.4 mm, 10.4 mm height |
| Core material | Ferrite, magnetically shielded |
| Operating temperature | -40 °C to +125 °C (ambient plus self-temperature rise) |
| Moisture sensitivity level | MSL 1 |
| RoHS | Compliant (-R suffix) |
At zero bias the winding measures 330 nH. Put Isat1 through it and the figure falls to 230 nH, about 30% lower, because the ferrite is partly saturated. Ripple calculations belong on the 330 nH number; loop stability and worst-case current belong on the lower one.
Peak current at 20% roll-off is 30 A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.
Copper loss at the rated current works out at about 462 mW (50 A squared times 0.185 mOhm). That is the term the Irms rating measures. The missing term is core loss, and at a few hundred kilohertz it can be the larger of the two.
Core loss needs flux, and flux here is about 110.2 mT for a 9 A ripple (K = 371). Double the ripple and the flux roughly doubles, but the loss does not - it climbs faster than linearly, which is why pushing ripple up to save inductance is not free.
The 9.6 x 6.4 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 330 nH this sits at the high-inductance end of the family. Ripple is small and core loss with it, but there is less headroom before saturation, because saturation current falls as inductance rises in the same can.
That makes it part 11 of 12 when the data sheet is sorted by inductance, with the highest DCR in the series at 0.185 mOhm, which is what the extra turns cost, Irms of 50 A is the bottom of the family.
Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 330 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.
Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.185 mOhm the winding is not the loss, the trace can be.
Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

How is the part packed?
Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.
Is this part AEC-Q200 qualified?
No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.
Shenzhen Gaorunxin Technology Co., Ltd
Shenzhen Gaorunxin Technology Co., Ltd