Eaton FP1010R3-R150-R 78 A SMD Power Inductor, 150 nH
Eaton FP1010R3-R150-R 78 A SMD Power Inductor, 150 nH

Eaton FP1010R3-R150-R 78 A SMD Power Inductor, 150 nH

Share
pEaton FP1010R3-R150-R: 150 nH high frequency, high current power inductor, 78 A Irms, 60 A Isat, DCR 0.145 mOhm, 9.6 x 6.4 mm package./p
    • Product Details
    • Download

    FP1010R3-R150-R at a glance: 150 nH high frequency, high current power inductor, 78 A Irms, 60 A Isat, DCR 0.145 mOhm, 9.6 x 6.4 mm body, 10.4 mm tall.

    Eaton FP1010R3-R150-R High frequency, high current power inductors

    The FP1010R3-R150-R is a 9.6 x 6.4 mm high frequency, high current power inductor from Eaton, rated 78 A Irms at 150 nH and 0.145 mOhm typical DCR. It is a surface-mount part 10.4 mm tall, operating from -40 °C to +125 °C, and it is built for the phase node of a buck regulator where the inductor sets ripple and the control loop sets the rest.

    Specification Table

    Orderable part numberFP1010R3-R150-R
    Inductance, OCL (0 Adc)150 nH
    Inductance, FLL (minimum)100 nH
    Irms (40 °C rise, no core loss)78 A
    Isat (20% roll-off @ +25 °C)60 A
    Isat2 (20% roll-off @ +75 °C)54 A
    Isat3 (20% roll-off @ +100 °C)52 A
    Isat4 (20% roll-off @ +125 °C)49 A
    DCR typical @ +20 °C0.145 mOhm
    K-factor (Bp-p = K x L x dI)432
    Package9.6 x 6.4 mm, 10.4 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    Moisture sensitivity levelMSL 1
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    Two inductance figures are published. 150 nH is measured with no DC in the winding, 100 nH with the winding loaded to Isat1. The gap between them is 33%, and it is the reason a converter that looks well damped at no load can ring at full current.

    Saturation is quoted as 20% roll-off at 60 A at +25 °C. That is a convention rather than a cliff: past it the inductance keeps falling, and how quickly depends on how hard the core is driven. Compare your worst-case peak against this number, not the average current.

    The 882 mW dissipated at 78 A through 0.145 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.

    The K-factor of 432 turns ripple into flux: a peak-to-peak swing of 18 A gives about 116.6 mT peak in the core. Read the material loss curve at that flux and your switching frequency to get the loss term Irms leaves out.

    Where This Part Sits in the Range

    The 9.6 x 6.4 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 150 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it part 5 of 12 when the data sheet is sorted by inductance, and it shares the lowest DCR here at 0.145 mOhm, Irms of 78 A is the top of the family.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs), Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Design Notes

    The order of checks that works: compute ripple from 150 nH and the duty cycle, add half of it to the DC load to get peak, compare that peak with Isat at the real ambient, and only then look at Irms for heating. Doing it the other way round hides saturation problems.

    On the board, place the part so the switch-node copper is short and wide. At 0.145 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Outline Drawing

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP1010R3-R150-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Why does DCR have both a typical and a maximum figure?
    The typical value is what the winding measures in production, the maximum is the limit the part is guaranteed to stay under. Size conduction loss on the maximum, because that is the worst case across a production run and over temperature.

    What does the R suffix on the part number mean?
    It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message