Eaton FP1010R3-R330-R 78 A SMD Power Inductor, 330 nH
Eaton FP1010R3-R330-R 78 A SMD Power Inductor, 330 nH

Eaton FP1010R3-R330-R 78 A SMD Power Inductor, 330 nH

Share
pEaton FP1010R3-R330-R: 330 nH high frequency, high current power inductor, 78 A Irms, 20 A Isat, DCR 0.145 mOhm, 9.6 x 6.4 mm package./p
    • Product Details
    • Download

    FP1010R3-R330-R at a glance: 330 nH high frequency, high current power inductor, 78 A Irms, 20 A Isat, DCR 0.145 mOhm, 9.6 x 6.4 mm body, 10.4 mm tall.

    Eaton FP1010R3-R330-R High frequency, high current power inductors

    Eaton builds the FP1010R3-R330-R as a high frequency, high current power inductor for 9.6 x 6.4 mm footprints. At 330 nH and 78 A Irms with 0.145 mOhm of DCR it targets high-current DC-DC stages; the 10.4 mm tall body keeps the height budget in check, and the part is rated from -40 °C to +125 °C.

    Key Specifications

    Orderable part numberFP1010R3-R330-R
    Inductance, OCL (0 Adc)330 nH
    Inductance, FLL (minimum)237 nH
    Irms (40 °C rise, no core loss)78 A
    Isat (20% roll-off @ +25 °C)20 A
    Isat2 (20% roll-off @ +75 °C)19 A
    Isat3 (20% roll-off @ +100 °C)17 A
    Isat4 (20% roll-off @ +125 °C)16 A
    DCR typical @ +20 °C0.145 mOhm
    K-factor (Bp-p = K x L x dI)432
    Package9.6 x 6.4 mm, 10.4 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    Moisture sensitivity levelMSL 1
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    330 nH open-circuit, 237 nH at full load: that is a 28% roll-off purely from DC bias, before temperature enters the picture. Use the biased figure when you check peak current against saturation, and the unbiased one when you size the ripple.

    Saturation is quoted as 20% roll-off at 20 A at +25 °C. That is a convention rather than a cliff: past it the inductance keeps falling, and how quickly depends on how hard the core is driven. Compare your worst-case peak against this number, not the average current.

    Copper loss at the rated current works out at about 882 mW (78 A squared times 0.145 mOhm). That is the term the Irms rating measures. The missing term is core loss, and at a few hundred kilohertz it can be the larger of the two.

    Core loss needs flux, and flux here is about 85.5 mT for a 6 A ripple (K = 432). Double the ripple and the flux roughly doubles, but the loss does not - it climbs faster than linearly, which is why pushing ripple up to save inductance is not free.

    Where This Part Sits in the Range

    The 9.6 x 6.4 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 330 nH this sits at the high-inductance end of the family. Ripple is small and core loss with it, but there is less headroom before saturation, because saturation current falls as inductance rises in the same can.

    That makes it part 11 of 12 when the data sheet is sorted by inductance, and it shares the lowest DCR here at 0.145 mOhm, Irms of 78 A is the top of the family.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs), Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Design Notes

    Size the inductor on peak current first, not average. With 330 nH the ripple can be a large fraction of the DC term at low inductance, so the peak may be well above the load current - and saturation cares about the peak.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.145 mOhm the winding is not the loss, the trace can be.

    Mechanical Dimensions and Pad Layout

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP1010R3-R330-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    What does the R suffix on the part number mean?
    It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.

    How is the part packed?
    Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products